Failed to open create the internal network Vagrant on Windows10

Question

I upgraded my Windows 10 to the last update yesterday and now  when I launch  vagrant up command  I get this error       gt  default  Booting VM       gt  default  Waiting for machine to boot  This may take a few minutes    The guest machine entered an invalid state while waiting for it to boot  Valid states are  starting  running   The machine is in the  poweroff  state  Please verify everything is configured properly and try again   If the provider you re using has a GUI that comes with it  it is often helpful to open that and watch the machine  since the GUI often has more helpful error messages than Vagrant can retrieve  For example  if you re using VirtualBox  run  vagrant up  while the VirtualBox GUI is open   The primary issue for this error is that the provider you re using is not properly configured  This is very rarely a Vagrant issue    When I try with GUI I have this error    Failed to open create the internal network  HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter   VERR INTNET FLT IF NOT FOUND   Failed to attach the network LUN  VERR INTNET FLT IF NOT FOUND     I have re-installed VirtualBox 5 0 10 and the extension pack  reconfigured Host-Only Ethernet Adapter  but always the same error     Any ideas

User · Answer

for me  I had to delete the  virtualbox  amp   docker folder In my user directory    which worked out fine

User · Answer

I had the same problem after upgrading from Windows 7 to Windows 10  Tried all the popular answers which did not work  Finally  I understood that Windows had changed the name of the adapter  Virtual Box was configured to use Realtek PCIe GBE Family Controller while device manager had this as Realtek PCIe GBE Family Controller  2  Selecting proper controller fixed the problem

User · Answer

After a Windows 10 update my VirtualBox Host-Only Ethernet Adapter was actually gone from the OS  network adapters  view these under Control Panel -  Network and Sharing Center -  Change adapter settings   Had to reinstall VirtualBox to bring that back to the OS    Then in the newer version of VirtualBox  the host-only adapters are under Global Tools  top right  -  Host Network Manager  Make sure the DHCP Server is enabled for the adapter   Example config

User · Answer

I tried the above options  but in vain  Eventually I uninstalled docker-toolbox  1 11 x  and virtualbox 5 16 x  and CHECKED the following option in the docker-toolbox installer GUI  by default the NDIS5 option was unchecked     Also the virtualadapter in network connections had  Bridge Networking Driver  option UNCHECKED and that worked fine for me

User · Answer

The same error occurred when I updated Windows  Tried everything  Nothing worked   Finally  went to Device Manager-  Network Adapters Disabled and enabled the Virtualbox Host only Adapter  And it worked

User · Answer

Uninstall Virtualbox and install the latest version  at the time of this answer it s 5 12  I installed Vagrant which automatically installed Virtualbox 5 10  I ran into this issue after installing the Windows 1511 update  uninstalling the Vagrant provided Virtualbox and installing the latest version fixed this

User · Answer

I tried every single thing on this page  and thanks everyone     Nothing worked   After literally hours and hours  I finally got it working   My problem was that I had no error preceding  something went wrong in step   Checking status on default        This line in the start sh script failed   VM STATUS     set  e      DOCKER MACHINE   status    VM        Running the following line from the Command Prompt worked and returned  Running    D  Dev DockerToolbox docker-machine exe status default   So I started following all the fixes in Github link and found the fix   In the start sh script  I changed the line  VM STATUS     set  e      DOCKER MACHINE   status    VM        to  VM STATUS      DOCKER MACHINE  status   VM

User · Answer

If the accepted https   stackoverflow com a 33733454 8520387 doesn t work for you  then disable other enabled Ethernet Cards  After this try to run your vagrant script again and it will create a new Network Card for you  For me it was  3

User · Answer

ON WINDOWS 10 After spending 3 frustrating hours of uninstalling  amp  re-installing minikube  virtualbox that did not resolve the problem  I saw the network adapters in my Control Panel- Network and Internet- Network Connections window  There were 3 enabled  VirtualBox Host-Only Ethernet Adapter  ones  I disabled them all   Then on services screen  run- services msc  find the Tcp Ip NetBIOS helper and restart it   A new network adapter with a proper name like  VirtualBox Host-Only Network  3  will be created  Now type      minikube delete     mnikube start It worked for me  hope It helped someone  I hate this

User · Answer

My solution was updating VirtualBox   I first ran into this issue after fresh install of Docker toolbox v1 12 5  on my Windows 8 1  What worked for me was update of VirtualBox  Then I had the same problem after some Windows Update  and updating VirtualBox fixed the issue again

User · Answer

Open Network and Sharing Center and go to the Change adapter settings in the sidebar   Right-click on the host-only adapter in the list of adapters and then Configure button - gt  Driver tab - gt  Update driver button   Select Browse my computer     and in the next dialog select Let me pick      You should see the list with just host-only driver in it   Select it and click next  After the driver is updated  please try using host-only network in a VM again

User · Answer

I found a solution   Open Windows Network Connections Right click on VirtualBox Host only adapter that created Choose properties Check  VirtualBox NDIS6 Bridged Networking driver  disable and Enable the adapter

User · Answer

I just ran into this problem with VirtualBox 5 1 on Windows 8  It turns out the problem was with the Kaspersky virus protection I have installed  It added the  Kaspersky Anti-Virus NDIS 6 Filter  on the host-only adapter on the windows side  When I disabled that filter the VM started properly

User · Answer

Open Control Panel  gt  gt  Network and Sharing Center  Now click on Change Adapter Settings  Right click on the adapter whose Name or the Device Name matches with VirtualBox Host-Only Ethernet Adapter   3 and click on Properties  Click on the Configure button  Now click on the Driver tab  Click on Update Driver  Select Browse my computer for drivers  Now choose Let me pick from a list of available drivers on my computer  Select the choice you get and click on Next  Click Close to finish the update  Now go back to your Terminal Powershell Command window and repeat the vagrant up command  It should work fine this time   https   www howtoforge com setup-a-local-wordpress-development-environment-with-vagrant

User · Answer

Fo me  updating VirtualBox to 5 1 23 fixed the issue  You can download this version for Windows from the official website

User · Answer

I have Windows 8 1 and had this problem with VirtualBox 5 0 16 105871  I tried every suggestion I found here  virtual box site  and other forums  None worked for me  I had this error when tried to start a VM with host-only interface   Failed to open a session for the virtual machine LinuxVMDev0   Failed to open create the internal network  HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter   VERR INTNET FLT IF NOT FOUND    Failed to attach the network LUN  VERR INTNET FLT IF NOT FOUND    Result Code  E FAIL  0x80004005  Component  ConsoleWrap Interface  IConsole  872da645-4a9b-1727-bee2-5585105b9eed    Finally the only solution that worked for me was    Uninstall 5 0 16 Install version 4 3 36 that did not have this problem  at least in my PC  Without uninstalling 4 3 36  install version 5 0 16 in the default way    Always installing as Administrator  i e  running the installer as administrator    That worked for me after trying different solution during days

User · Answer

You can try disabling the  VirtualBox NDIS6 Bridged Networking Driver  on all but your actual physical network adapter s  before attempting to create the VirtualBox host-only adapter again   See this answer

User · Answer

I found a solution for my problem   There was a conflict in my network adapters  I simply disabled the one who appears in the error message  then started again the running command  and a new adapter has been created after many approval messages from windows   I hope this solution could help in some cases

User · Answer

Reboot your PC    Sadly  https   stackoverflow com a 33733454 2191572 did not work for me in Windows 10 x64 with VirtualBox 5 2 6  The box was already checked and a simple reboot fixed it   After years of telling people to just reboot  I failed to follow my own golden advice  face  meet palm

User · Answer

The two answers did not solve my issue but combining them  I was able to solve the problem  My situation was I was trying to install and run Docker on a Windows 7 pc and kept getting an error   Looks like something went wrong    Press any key to continue      After much digging  I was able to relate the issue to the host network adapter that was created by Docker  I had the NDIS6 driver installed but it was enabled  I tried to uncheck  disable  recheck  enable etc but it did not help   I then uninstalled VB and reinstalled as per the first answer to get the NDIS5 driver   This was unchecked  so checking it I was able to move past this issue

User · Answer

There is a known issue with the new NDIS6 driver  you can install it to use the NDIS5 driver  Try reinstalling it with a parameter  Run as administrator    gt  VirtualBox-5 0 11-104101-Win exe -msiparams NETWORKTYPE NDIS5  This worked for me   Update  Newer versions made it easier to pick the NDIS driver from within the installation wizard - just pick NDIS5 when asked   ref  https   www virtualbox org manual ch02 html install-win-performing

User · Answer

I have worked around for a while  all you need to do is open VirtualBox    File   Preferences   Network   Host-Only Networks  You will see VirtualBox Host-Only Ethernet Adapter  click on it  and edit   My IP settings for vagrant VM was 192 168 10 10  you should edit up to your VM IP  Here is my adapter settings   Adapter Settings  DHCP Server Settings

User · Answer

For me  disable and enable the network connection wasn t enough to make it work  I had to delete the content of the  docker repository in my home user  c  Users your user  docker    After doing that i reinstall Docker Toolbox and VitualBox and use machzqcq tips to check the install virtualbox with NDIS5 driver   I found the answer here   https   github com docker toolbox issues 473

[vagrant] Failed to open/create the internal network Vagrant on Windows10

Examples related to vagrant

Examples related to virtualbox

Examples related to windows-10