An alternative is to use the Alpine Linux containers, e.g. python:2.7-alpine. They offer pip out of the box (and have a smaller footprint which leads to faster builds etc).

Read Byte by Byte and check that each byte against '\n' if it is not, then store it into buffer
if it is '\n' add '\0' to buffer and then use atoi()

You can read a single byte like this

char c;
read(fd,&c,1);

See read()

I've solved my problems, so I post here the correct code in case someone needs similar stuff.

Open Port

int USB = open( "/dev/ttyUSB0", O_RDWR| O_NOCTTY );

Set parameters

struct termios tty;
struct termios tty_old;
memset (&tty, 0, sizeof tty);

/* Error Handling */
if ( tcgetattr ( USB, &tty ) != 0 ) {
   std::cout << "Error " << errno << " from tcgetattr: " << strerror(errno) << std::endl;
}

/* Save old tty parameters */
tty_old = tty;

/* Set Baud Rate */
cfsetospeed (&tty, (speed_t)B9600);
cfsetispeed (&tty, (speed_t)B9600);

/* Setting other Port Stuff */
tty.c_cflag     &=  ~PARENB;            // Make 8n1
tty.c_cflag     &=  ~CSTOPB;
tty.c_cflag     &=  ~CSIZE;
tty.c_cflag     |=  CS8;

tty.c_cflag     &=  ~CRTSCTS;           // no flow control
tty.c_cc[VMIN]   =  1;                  // read doesn't block
tty.c_cc[VTIME]  =  5;                  // 0.5 seconds read timeout
tty.c_cflag     |=  CREAD | CLOCAL;     // turn on READ & ignore ctrl lines

/* Make raw */
cfmakeraw(&tty);

/* Flush Port, then applies attributes */
tcflush( USB, TCIFLUSH );
if ( tcsetattr ( USB, TCSANOW, &tty ) != 0) {
   std::cout << "Error " << errno << " from tcsetattr" << std::endl;
}

Write

unsigned char cmd[] = "INIT \r";
int n_written = 0,
    spot = 0;

do {
    n_written = write( USB, &cmd[spot], 1 );
    spot += n_written;
} while (cmd[spot-1] != '\r' && n_written > 0);

It was definitely not necessary to write byte per byte, also int n_written = write( USB, cmd, sizeof(cmd) -1) worked fine.

At last, read:

int n = 0,
    spot = 0;
char buf = '\0';

/* Whole response*/
char response[1024];
memset(response, '\0', sizeof response);

do {
    n = read( USB, &buf, 1 );
    sprintf( &response[spot], "%c", buf );
    spot += n;
} while( buf != '\r' && n > 0);

if (n < 0) {
    std::cout << "Error reading: " << strerror(errno) << std::endl;
}
else if (n == 0) {
    std::cout << "Read nothing!" << std::endl;
}
else {
    std::cout << "Response: " << response << std::endl;
}

This one worked for me. Thank you all!

Copy a file in a sane way:

#include <fstream>

int main()
{
    std::ifstream  src("from.ogv", std::ios::binary);
    std::ofstream  dst("to.ogv",   std::ios::binary);

    dst << src.rdbuf();
}

This is so simple and intuitive to read it is worth the extra cost. If we were doing it a lot, better to fall back on OS calls to the file system. I am sure boost has a copy file method in its filesystem class.

There is a C method for interacting with the file system:

#include <copyfile.h>

int
copyfile(const char *from, const char *to, copyfile_state_t state, copyfile_flags_t flags);

#include <stdbool.h>

For someone like me here to copy and paste.

readelf -a xxx

 INTERP         
  0x0000000000000238 0x0000000000400238 0x0000000000400238           
  0x000000000000001c 0x000000000000001c  R      1
  [Requesting program interpreter: /lib64/ld-linux-x86-64.so.2]

On Linux you can also use:

struct timeval timeout;
timeout.tv_sec  = 7;  // after 7 seconds connect() will timeout
timeout.tv_usec = 0;
setsockopt(fd, SOL_SOCKET, SO_SNDTIMEO, &timeout, sizeof(timeout));
connect(...)

Don't forget to clear SO_SNDTIMEO after connect() if you don't need it.

You have to do write in the same loop as read.

On Linux and BSD you can directly create the socket in non-blocking mode (https://www.man7.org/linux/man-pages/man7/socket.7.html):

int fd = socket(res->ai_family, res->ai_socktype | SOCK_NONBLOCK | SOCK_CLOEXEC, res->ai_protocol);
if (fd == -1) {
    perror("socket");
    return -1;
}

When accepting connections you can use the accept4 function to directly accept new connections in non-blocking mode (https://man7.org/linux/man-pages/man2/accept.2.html):

int fd = accept4(lfd, NULL, 0, SOCK_NONBLOCK | SOCK_CLOEXEC);
if (fd == -1) {
    perror("accept4");
    return -1;
}

I don't know why the accepted answer doesn't mention this.

Although this does not help you right away, there is an alternative that can work with both Unix (fcntl) and Windows (win32 api calls), called: portalocker

It describes itself as a cross-platform (posix/nt) API for flock-style file locking for Python. It basically maps fcntl to win32 api calls.

The original code at http://code.activestate.com/recipes/65203/ can now be installed as a separate package - https://pypi.python.org/pypi/portalocker

Looking at the output of free -m it seems to me that you actually do not have swap memory available. I am not sure if in Linux the swap always will be available automatically on demand, but I was having the same problem and none of the answers here really helped me. Adding some swap memory however, fixed the problem in my case so since this might help other people facing the same problem, I post my answer on how to add a 1GB swap (on Ubuntu 12.04 but it should work similarly for other distributions.)

You can first check if there is any swap memory enabled.

$sudo swapon -s

if it is empty, it means you don't have any swap enabled. To add a 1GB swap:

$sudo dd if=/dev/zero of=/swapfile bs=1024 count=1024k
$sudo mkswap /swapfile
$sudo swapon /swapfile

Add the following line to the fstab to make the swap permanent.

$sudo vim /etc/fstab

     /swapfile       none    swap    sw      0       0 

Source and more information can be found here.

I believe fcntl() is a POSIX function. Where as ioctl() is a standard UNIX thing. Here is a list of POSIX io. ioctl() is a very kernel/driver/OS specific thing, but i am sure what you use works on most flavors of Unix. some other ioctl() stuff might only work on certain OS or even certain revs of it's kernel.

(char)myint;

for example:

Console.WriteLine("(char)122 is {0}", (char)122);

yields:

(char)122 is z

You can disable constraints in Oracle but not indexes. There's a command to make an index ununsable but you have to rebuild the index anyway, so I'd probably just write a script to drop and rebuild the indexes. You can use the user_indexes and user_ind_columns to get all the indexes for a schema or use dbms_metadata:

select dbms_metadata.get_ddl('INDEX', u.index_name) from user_indexes u;

Try AhtiK Eclipse WordWrap, it works for me: http://www.ahtik.com/eclipse-update/

That happened to me too, because I was trying to get an IEnumerable but the response had a single value. Please try to make sure it's a list of data in your response. The lines I used (for api url get) to solve the problem are like these:

HttpResponseMessage response = await client.GetAsync("api/yourUrl");

if (response.IsSuccessStatusCode)
{
    IEnumerable<RootObject> rootObjects =
        awaitresponse.Content.ReadAsAsync<IEnumerable<RootObject>>();

    foreach (var rootObject in rootObjects)
    {
        Console.WriteLine(
            "{0}\t${1}\t{2}",
            rootObject.Data1, rootObject.Data2, rootObject.Data3);
    }

    Console.ReadLine();
}

Hope It helps.

The easy way to get Windows to tell you the answer is to attempt to rename a file via Explorer and type in / for the new name. Windows will popup a message box telling you the list of illegal characters.

A filename cannot contain any of the following characters:
    \ / : * ? " < > | 

https://support.microsoft.com/en-us/kb/177506

import pandas as pd
df = pd.DataFrame([{'Product': 'Coke', 'Prices': [100,123,101,105,99,94,98]},{'Product': 'Pepsi', 'Prices': [101,104,104,101,99,99,99]}])
print(df)
df = df.assign(Prices=df.Prices.str.split(',')).explode('Prices')
print(df)

Try this in pandas >=0.25 version

I know the solution employing printing of new lines isn't much supported, but if all else fails, why not? Especially where one is operating in an environment where someone else is likely to be able to see the screen, yet not able to keylog. One potential solution then, is the following alias:

alias c="printf '\r\n%.0s' {1..50}"

Then, to "clear" away the current contents of the screen (or rather, hide them), just type c+Enter at the terminal.

try this one

String fileSuffix = new SimpleDateFormat("yyyyMMddHHmmss").format(new Date());

Below code will help you to find out iframe data.

let iframe = document.getElementById('frameId');
let innerDoc = iframe.contentDocument || iframe.contentWindow.document;

Use LinkedList instead. Than, you can create an array if necessary.

Nothing stops you from doing the above, but hold up!

There are some gotchas. Assignment in Javascript is from right to left so when you write:

var moveUp = moveDown = moveLeft = moveRight = mouseDown = touchDown = false;

it effectively translates to:

var moveUp = (moveDown = (moveLeft = (moveRight = (mouseDown = (touchDown = false)))));

which effectively translates to:

var moveUp = (window.moveDown = (window.moveLeft = (window.moveRight = (window.mouseDown = (window.touchDown = false)))));

Inadvertently, you just created 5 global variables--something I'm pretty sure you didn't want to do.

Note: My above example assumes you are running your code in the browser, hence window. If you were to be in a different environment these variables would attach to whatever the global context happens to be for that environment (i.e., in Node.js, it would attach to global which is the global context for that environment).

Now you could first declare all your variables and then assign them to the same value and you could avoid the problem.

var moveUp, moveDown, moveLeft, moveRight, mouseDown, touchDown;
moveUp = moveDown = moveLeft = moveRight = mouseDown = touchDown = false;

Long story short, both ways would work just fine, but the first way could potentially introduce some pernicious bugs in your code. Don't commit the sin of littering the global namespace with local variables if not absolutely necessary.

Sidenote: As pointed out in the comments (and this is not just in the case of this question), if the copied value in question was not a primitive value but instead an object, you better know about copy by value vs copy by reference. Whenever assigning objects, the reference to the object is copied instead of the actual object. All variables will still point to the same object so any change in one variable will be reflected in the other variables and will cause you a major headache if your intention was to copy the object values and not the reference.

You shouldn't. If you want to do such a thing either you need to force user to use a single instance of your application by writing URLs on the fly use a sessionID alike (not sessionid it won't work) id and pass it in every URL.

I don't know why you need it but unless you need make a totally unusable application don't do it.

Use PHP Rand function

<?php
  $input = array("Neo", "Morpheus", "Trinity", "Cypher", "Tank");
  $rand_keys = array_rand($input, 2);
  echo $input[$rand_keys[0]] . "\n";
  echo $input[$rand_keys[1]] . "\n";
?>

More Help

You can simply add this line into your bootstrap_and_overides.css.less file

body { background: #000000 !important;}

that's it

An alternative could be to use the new JSON extension for SQLite. I've only just come across this myself: https://www.sqlite.org/json1.html This would allow you to perform a certain level of querying the stored JSON. If you used VARCHAR or TEXT to store a JSON string you would have no ability to query it. This is a great article showing its usage (in python) http://charlesleifer.com/blog/using-the-sqlite-json1-and-fts5-extensions-with-python/

I added this for pages that were too short.

html:

<section id="secondary-foot"></section>

css:

section#secondary-foot {
    height: 100%;
    background-color: #000000;
    position: fixed;
    width: 100%;
}

I can't comment on the above answer, but be careful with @Pavel Chuchuva's answer. That formula will not return a result if both coordinates are the same. In that case, distance is null, and so that row won't be returned with that formula as is.

I'm not a MySQL expert, but this seems to be working for me:

SELECT id, ( 3959 * acos( cos( radians(37) ) * cos( radians( lat ) ) * cos( radians( lng ) - radians(-122) ) + sin( radians(37) ) * sin( radians( lat ) ) ) ) AS distance 
FROM markers HAVING distance < 25 OR distance IS NULL ORDER BY distance LIMIT 0 , 20;

You can try this:

HTML

<table>
    <tr>
        <td class="shrink">element1</td>
        <td class="shrink">data</td>
        <td class="shrink">junk here</td>
        <td class="expand">last column</td>
    </tr>
    <tr>
        <td class="shrink">elem</td>
        <td class="shrink">more data</td>
        <td class="shrink">other stuff</td>
        <td class="expand">again, last column</td>
    </tr>
    <tr>
        <td class="shrink">more</td>
        <td class="shrink">of </td>
        <td class="shrink">these</td>
        <td class="expand">rows</td>
    </tr>
</table>

CSS

table {
    border: 1px solid green;
    border-collapse: collapse;
    width:100%;
}

table td {
    border: 1px solid green;
}

table td.shrink {
    white-space:nowrap
}
table td.expand {
    width: 99%
}

While it may work on some platforms, be aware that platform.architecture is not always a reliable way to determine whether python is running in 32-bit or 64-bit. In particular, on some OS X multi-architecture builds, the same executable file may be capable of running in either mode, as the example below demonstrates. The quickest safe multi-platform approach is to test sys.maxsize on Python 2.6, 2.7, Python 3.x.

$ arch -i386 /usr/local/bin/python2.7
Python 2.7.9 (v2.7.9:648dcafa7e5f, Dec 10 2014, 10:10:46)
[GCC 4.2.1 (Apple Inc. build 5666) (dot 3)] on darwin
Type "help", "copyright", "credits" or "license" for more information.
>>> import platform, sys
>>> platform.architecture(), sys.maxsize
(('64bit', ''), 2147483647)
>>> ^D
$ arch -x86_64 /usr/local/bin/python2.7
Python 2.7.9 (v2.7.9:648dcafa7e5f, Dec 10 2014, 10:10:46)
[GCC 4.2.1 (Apple Inc. build 5666) (dot 3)] on darwin
Type "help", "copyright", "credits" or "license" for more information.
>>> import platform, sys
>>> platform.architecture(), sys.maxsize
(('64bit', ''), 9223372036854775807)

Online tools to translate Apache .htaccess to Nginx rewrite tools include:

• http://winginx.com/htaccess
• http://www.anilcetin.com/convert-apache-htaccess-to-nginx/

Note that these tools will convert to equivalent rewrite expressions using if statements, but they should be converted to try_files. See:

• http://wiki.nginx.org/NginxHttpCoreModule#try_files

Not possible with standard unix commands. You might have luck with a file recovery utility. Also, be aware, using rm changes the table of contents to mark those blocks as available to be overwritten, so simply using your computer right now risks those blocks being overwritten permanently. If it's critical data, you should turn off the computer before the file sectors gets overwritten. Good luck!

Some restore utility: http://www.ubuntugeek.com/recover-deleted-files-with-foremostscalpel-in-ubuntu.html

Forum where this was previously answered: http://webcache.googleusercontent.com/search?q=cache:m4hiPw-_GekJ:ubuntuforums.org/archive/index.php/t-1134955.html+&cd=1&hl=en&ct=clnk&gl=us

Try This:

$url = "http://www.google.com/search?q=".$strSearch."&hl=en&start=0&sa=N";
  $ch = curl_init();
  curl_setopt($ch, CURLOPT_HEADER, 0);
  curl_setopt($ch, CURLOPT_VERBOSE, 0);
  curl_setopt($ch, CURLOPT_RETURNTRANSFER, true);
  curl_setopt($ch, CURLOPT_USERAGENT, "Mozilla/4.0 (compatible;)");
  curl_setopt($ch, CURLOPT_URL, urlencode($url));
  $response = curl_exec($ch);
  curl_close($ch);

Examples

Given the string foobarbarfoo:

bar(?=bar)     finds the 1st bar ("bar" which has "bar" after it)
bar(?!bar)     finds the 2nd bar ("bar" which does not have "bar" after it)
(?<=foo)bar    finds the 1st bar ("bar" which has "foo" before it)
(?<!foo)bar    finds the 2nd bar ("bar" which does not have "foo" before it)

You can also combine them:

(?<=foo)bar(?=bar)    finds the 1st bar ("bar" with "foo" before it and "bar" after it)

Definitions

Look ahead positive (?=)

Find expression A where expression B follows:

A(?=B)

Look ahead negative (?!)

Find expression A where expression B does not follow:

A(?!B)

Look behind positive (?<=)

Find expression A where expression B precedes:

(?<=B)A

Look behind negative (?<!)

Find expression A where expression B does not precede:

(?<!B)A

Atomic groups (?>)

An atomic group exits a group and throws away alternative patterns after the first matched pattern inside the group (backtracking is disabled).

• (?>foo|foot)s applied to foots will match its 1st alternative foo, then fail as s does not immediately follow, and stop as backtracking is disabled

A non-atomic group will allow backtracking; if subsequent matching ahead fails, it will backtrack and use alternative patterns until a match for the entire expression is found or all possibilities are exhausted.

• (foo|foot)s applied to foots will:

  1. match its 1st alternative foo, then fail as s does not immediately follow in foots, and backtrack to its 2nd alternative;
  2. match its 2nd alternative foot, then succeed as s immediately follows in foots, and stop.

Some resources

• http://www.regular-expressions.info/lookaround.html
• http://www.rexegg.com/regex-lookarounds.html

Online testers

• https://regex101.com

If you're looking to post data to a URL from PHP code itself (without using an html form) it can be done with curl. It will look like this:

$url = 'http://www.someurl.com';
$myvars = 'myvar1=' . $myvar1 . '&myvar2=' . $myvar2;

$ch = curl_init( $url );
curl_setopt( $ch, CURLOPT_POST, 1);
curl_setopt( $ch, CURLOPT_POSTFIELDS, $myvars);
curl_setopt( $ch, CURLOPT_FOLLOWLOCATION, 1);
curl_setopt( $ch, CURLOPT_HEADER, 0);
curl_setopt( $ch, CURLOPT_RETURNTRANSFER, 1);

$response = curl_exec( $ch );

This will send the post variables to the specified url, and what the page returns will be in $response.

If you need to have from mysql, after your query, the last auto-incremental id without another query, put in your code:

mysql_insert_id();

If you landed here looking for solution that works with React Router and AWS Amplify Console - you already know that you can't use CloudFront redirection rules directly since Amplify Console does not expose CloudFront Distribution for the app.

Solution, however, is very simple - you just need to add a redirect/rewrite rule in Amplify Console like this:

See the following links for more info (and copy-friendly rule from the screenshot):

• https://docs.aws.amazon.com/amplify/latest/userguide/redirects.html#redirects-for-single-page-web-apps-spa
• https://github.com/aws-amplify/amplify-console/issues/83

Thanks for the information. very helpful i used it for locking page interaction while in edit mode by another user. I used it in conjunction with ajaxComplete. Not necesarily the same behavior but somewhat similar.

function userPageLock(){
    $("body").bind("ajaxComplete.lockpage", function(){
        $("body").unbind("ajaxComplete.lockpage");
        executePageLock();      
    });
};  

function executePageLock(){
    //do something
}

As others said, you can't actually strictly do what you are asking for. That said, all of the tools available to the angular framework are actually available to you as well! What that means is you can actually write your own elements and provide this feature yourself. I wrote one of these up as an example which you can see at the following plunkr (http://plnkr.co/edit/Qrz9zFjc7Ud6KQoNMEI1).

The key parts of this are that I define a "clickable" element (don't do this if you need older IE support). In code that looks like:

<clickable>
  <h1>Hello World!</h1>
</clickable>

Then I defined a directive to take this clickable element and turn it into what I want (something that automatically sets up my click event):

app.directive('clickable', function() {
    return {
        transclude: true,
        restrict: 'E',
        template: '<div ng-transclude ng-click="handleClick($event)"></div>'
    };
});

Finally in my controller I have the click event ready to go:

$scope.handleClick = function($event) {
    var i = 0;
};

Now, its worth stating that this hard codes the name of the method that handles the click event. If you wanted to eliminate this, you should be able to provide the directive with the name of your click handler and "tada" - you have an element (or attribute) that you can use and never have to inject "$event" again.

Hope that helps!

Checkout the .SaveAs() method in Excel object.

wbWorkbook.SaveAs("c:\yourdesiredFilename.csv", Microsoft.Office.Interop.Excel.XlFileFormat.xlCSV)

Or following:

public static void SaveAs()
{
    Microsoft.Office.Interop.Excel.Application app = new Microsoft.Office.Interop.Excel.ApplicationClass();
    Microsoft.Office.Interop.Excel.Workbook wbWorkbook = app.Workbooks.Add(Type.Missing);
    Microsoft.Office.Interop.Excel.Sheets wsSheet = wbWorkbook.Worksheets;
    Microsoft.Office.Interop.Excel.Worksheet CurSheet = (Microsoft.Office.Interop.Excel.Worksheet)wsSheet[1];

    Microsoft.Office.Interop.Excel.Range thisCell = (Microsoft.Office.Interop.Excel.Range)CurSheet.Cells[1, 1];

    thisCell.Value2 = "This is a test.";

    wbWorkbook.SaveAs(@"c:\one.xls", Microsoft.Office.Interop.Excel.XlFileFormat.xlWorkbookNormal, Type.Missing, Type.Missing, Type.Missing, Type.Missing, Microsoft.Office.Interop.Excel.XlSaveAsAccessMode.xlShared, Type.Missing, Type.Missing, Type.Missing, Type.Missing, Type.Missing);
    wbWorkbook.SaveAs(@"c:\two.csv", Microsoft.Office.Interop.Excel.XlFileFormat.xlCSVWindows, Type.Missing, Type.Missing, Type.Missing, Type.Missing, Microsoft.Office.Interop.Excel.XlSaveAsAccessMode.xlShared, Type.Missing, Type.Missing, Type.Missing, Type.Missing, Type.Missing);

    wbWorkbook.Close(false, "", true);
}

there are many ways. using wc is one.

wc -l file

others include

awk 'END{print NR}' file

sed -n '$=' file (GNU sed)

grep -c ".*" file

It looks like you're writing PHP, in which case you want:

<?
$arr=array('us'=>'United', 'ca'=>'canada');
$key='ca';
echo $arr[$key];
?>

Notice that the ('us'=>'United', 'ca'=>'canada') needs to be a parameter to the array function in PHP.

Most programming languages that support associative arrays or dictionaries use arr['key'] to retrieve the item specified by 'key'

For instance:

Ruby

ruby-1.9.1-p378 > h = {'us' => 'USA', 'ca' => 'Canada' }
 => {"us"=>"USA", "ca"=>"Canada"} 
ruby-1.9.1-p378 > h['ca']
 => "Canada" 

Python

>>> h = {'us':'USA', 'ca':'Canada'}
>>> h['ca']
'Canada'

C#

class P
{
    static void Main()
    {
        var d = new System.Collections.Generic.Dictionary<string, string> { {"us", "USA"}, {"ca", "Canada"}};
        System.Console.WriteLine(d["ca"]);
    }
}

Lua

t = {us='USA', ca='Canada'}
print(t['ca'])
print(t.ca) -- Lua's a little different with tables

Make sure that your <td> is not display: block;

Floating will do this, but much easier to just: display: inline;

This should do it:

UPDATE ProductReviews
SET    ProductReviews.status = '0'
FROM   ProductReviews
       INNER JOIN products
         ON ProductReviews.pid = products.id
WHERE  ProductReviews.id = '17190'
       AND products.shopkeeper = '89137'

First thing is first. You need to define $scope.telephone as an array in your controller before you can start using it in your view.

$scope.telephone = [];

To address the issue of ng-model not being recognised when you append a new input - for that to work you have to use the $compile Angular service.

From the Angular.js API reference on $compile:

Compiles an HTML string or DOM into a template and produces a template function, which can then be used to link scope and the template together.

// I'm using Angular syntax. Using jQuery will have the same effect
// Create input element
var input = angular.element('<div><input type="text" ng-model="telephone[' + $scope.inputCounter + ']"></div>');
// Compile the HTML and assign to scope
var compile = $compile(input)($scope);

Have a look on JSFiddle

Both ways are correct.

If you need to do something with the Exception object in the catch block then you should use

try {
    // code....
}
catch (Exception ex){}

and then use ex in the catch block.

Anyway, it is not always a good practice to catch the Exception class, it is a better practice to catch a more specific exception - an exception which you expect.

If you're stuck with SQL Server <2017, you can use GroupConcat. The syntax and the performance is far better than the FOR XML PATH sollution.

Installation:

-- https://codeplexarchive.blob.core.windows.net/archive/projects/groupconcat/groupconcat.zip
create assembly [GroupConcat] from 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with permission_set = safe;
create aggregate [dbo].[GROUP_CONCAT]    (@VALUE [nvarchar](4000))                                                      returns[nvarchar](max) external name [GroupConcat].[GroupConcat.GROUP_CONCAT];
create aggregate [dbo].[GROUP_CONCAT_D]  (@VALUE [nvarchar](4000), @DELIMITER [nvarchar](4))                            returns[nvarchar](max) external name [GroupConcat].[GroupConcat.GROUP_CONCAT_D];
create aggregate [dbo].[GROUP_CONCAT_DS] (@VALUE [nvarchar](4000), @DELIMITER [nvarchar](4), @SORT_ORDER [tinyint])     returns[nvarchar](max) external name [GroupConcat].[GroupConcat.GROUP_CONCAT_DS];
create aggregate [dbo].[GROUP_CONCAT_S]  (@VALUE [nvarchar](4000), @SORT_ORDER [tinyint])                               returns[nvarchar](max) external name [GroupConcat].[GroupConcat.GROUP_CONCAT_S];

go

Usage:

declare @liststr varchar(max)
select @liststr = dbo.group_concat_d(institutionname, ',')
from education
where studentnumber = '111'
group by studentnumber;
select @liststr

GroupConcat does not support ordering, though. You could use PIVOT, CTE's and windows functions if you need ordering:

drop table if exists #students;
create table #students (
    name        varchar(20),
    institution varchar(20),
    year        int -- order by year
)
go

insert into #students(name, institution, year)
values
    ('Simon', 'INSTITUTION1', 2005),
    ('Simon', 'INSTITUTION2', 2008);

with cte as (
    select name,
           institution,
           rn = row_number() over (partition by name order by year)
    from #students
)
select name,
       [1] +
       isnull((',' + [2]), '') +
       isnull((',' + [3]), '') +
       isnull((',' + [4]), '') +
       isnull((',' + [5]), '') +
       isnull((',' + [6]), '') +
       isnull((',' + [7]), '') +
       isnull((',' + [8]), '') +
       isnull((',' + [9]), '') +
       isnull((',' + [10]), '') +
       isnull((',' + [11]), '') +
       isnull((',' + [12]), '') +
       isnull((',' + [13]), '') +
       isnull((',' + [14]), '') +
       isnull((',' + [15]), '') +
       isnull((',' + [16]), '') +
       isnull((',' + [17]), '') +
       isnull((',' + [18]), '') +
       isnull((',' + [19]), '') +
       isnull((',' + [20]), '')
from cte
    pivot (
    max(institution)
    for rn in ([1], [2], [3], [4],[5],[6],[7],[8],[9],[10],[11],[12],[13],[14],[15],[16],[17],[18],[19],[20])
    ) as piv

For bootstrap datetimepicker, assign decade value as follow:

$(".years").datetimepicker({
    format: "yyyy",
    startView: 'decade',
    minView: 'decade',
    viewSelect: 'decade',
    autoclose: true,
});

Yes:

#include <iostream>
#include <functional>

struct null_ref_t {
   template <typename T>
   operator T&() {
      union TypeSafetyBreaker {
         T *ptr;

         // see https://stackoverflow.com/questions/38691282/use-of-union-with-reference
         std::reference_wrapper<T> ref; 
      };

      TypeSafetyBreaker ptr = {.ptr = nullptr};

      // unwrap the reference
      return ptr.ref.get();
   }
};

null_ref_t nullref;


int main() {
   int &a = nullref;

   // Segmentation fault
   a = 4;
   return 0;
}

To merge a local directory into a directory within an image, do this. It will not delete files already present within the image. It will only add files that are present locally, overwriting the files in the image if a file of the same name already exists.

COPY ./files/. /files/

I fixed this issue by setting a newer version of node as default in nvm i.e.:

nvm alias default 12.XX.X

Just a thought, but you may check the influence of a ulimit -v option.

That is not an actual solution since it would limit address space available for all process, but that would allow you to check the behavior of your application with a limited virtual memory.

There is actually no difference as both require 1 click:

• Eclipse: manual Save, auto-compile.
• IntelliJ: auto Save, manual compile.

Simplest solution is just to get used to it. Because when you spend most of your daytime in your IDE, then better have fast habits in one than slow habits in several of them.

At the risk of getting yet another mysterious down-vote...the fact that many mention the stack and memory with respect to value types and primitive types is because they must fit into a register in the microprocessor. You cannot push or pop something to/from the stack if it takes more bits than a register has....the instructions are, for example "pop eax" -- because eax is 32 bits wide on a 32-bit system.

Floating-point primitive types are handled by the FPU, which is 80 bits wide.

This was all decided long before there was an OOP language to obfuscate the definition of primitive type and I assume that value type is a term that has been created specifically for OOP languages.

Option 3 is your best bet, but not all DB engines have a "bit" type. If you don't have a bit, then TinyINT would be your best bet.

In addition to Roman's answer, something like this might be even simpler. Note that I haven't tested it because I do not have access to R right now.

# Note that I use a global variable here
# normally not advisable, but I liked the
# use here to make the code shorter
index <<- 0
new_column = sapply(df$h_no, function(x) {
  if(x == 1) index = index + 1
  return(index)
})

The function iterates over the values in n_ho and always returns the categorie that the current value belongs to. If a value of 1 is detected, we increase the global variable index and continue.

Assuming you're talking about US currency, you would want a Greedy Algorithm: http://en.wikipedia.org/wiki/Greedy_algorithm

In essence, you try all denominations from highest-to-lowest, taking as many coins as posible from each one until you've got nothing left.

For the general case see http://en.wikipedia.org/wiki/Change-making_problem, because you would want to use dynamic programming or linear programming to find the answer for arbitrary denominations where a greedy algorithm wouldn't work.

Here is the official microsoft VM images for doing IE 6, 7, 8 and 9 testing: http://www.microsoft.com/en-us/download/details.aspx?id=11575

I did like this..

Right click on the project--> configure-->convert to maven project. Right click on the project-->maven-->add dependencies.

I think C in fact supports pass by reference.

Most languages require syntactic sugar to pass by reference instead of value. (C++ for example requires & in the parameter declaration).

C also requires syntactic sugar for this. It's * in the parameter type declaration and & on the argument. So * and & is the C syntax for pass by reference.

One could now argue that real pass by reference should only require syntax on the parameter declaration, not on the argument side.

But now comes C# which does support by reference passing and requires syntactic sugar on both parameter and argument sides.

The argument that C has no by-ref passing cause the the syntactic elements to express it exhibit the underlying technical implementation is not an argument at all, as this applies more or less to all implementations.

The only remaining argument is that passing by ref in C is not a monolithic feature but combines two existing features. (Take ref of argument by &, expect ref to type by *.) C# for example does require two syntactic elements, but they can't be used without each other.

This is obviously a dangerous argument, cause lots of other features in languages are composed of other features. (like string support in C++)

If start time is a datetime type then you can use something like

SELECT BookingId, StartTime
FROM Booking
WHERE StartTime >= '2012-03-08 00:00:00.000' 
AND StartTime <= '2012-03-08 01:00:00.000'

Obviously you would want to use your own values for the times but this should give you everything in that 1 hour period inclusive of both the upper and lower limit.

You can use the GETDATE() function to get todays current date.

We are running Linux, a mostly POSIX-compliant OS. POSIX standards it should be: Utility Argument Syntax.

• An option is a hyphen followed by a single alphanumeric character, like this: -o.
• An option may require an argument (which must appear immediately after the option); for example, -o argument or -oargument.
• Options that do not require arguments can be grouped after a hyphen, so, for example, -lst is equivalent to -t -l -s.
• Options can appear in any order; thus -lst is equivalent to -tls.
• Options can appear multiple times.
• Options precede other nonoption arguments: -lst nonoption.
• The -- argument terminates options.
• The - option is typically used to represent one of the standard input streams.

Cocoa pods - reduce wait times to 10% ( on Mac OS ) :

1- type pod setup in your project folder ( first you have to be in the project folder) from terminal in Mac OS.

2- CTRL+z to stop after it creates master directory ( folder ) [you can see it in your cocoa pods folder location : ~/.cocoapods/repos]

3. Download .zip from 

   https://github.com/CocoaPods/Specs

    master branch ( its 301 MB) , Extract it . It will take approx 5-10 mins

4.Copy the content to ~/.cocoapods/repos ( now here you only need to copy the contents inside the master folder , so make sure that master folder is created already with pod setup command )

5- once you copy it ( or I should say move , drag and drop as copying will take forever , as its very large ), you can then do pod install --no-repo-update 6- your pods in the pod file now will start installing Here is a screenshot

Call the materialize css jquery code only after the html has rendered. So you can have a controller and then fire a service which calls the jquery code in the controller. This will render the select button alright. How ever if you try to use ngChange or ngSubmit it may not work due to the dynamic styling of the select tag.

I use this function which uses bc and thus supports floating point calculations:

c () { 
    local a
    (( $# > 0 )) && a="$@" || read -r -p "calc: " a
    bc -l <<< "$a"
}

Example:

$ c '5*5'
25
$ c 5/5
1.00000000000000000000
$ c 3.4/7.9
.43037974683544303797

Bash's arithmetic expansion doesn't support floats (but Korn shell and zsh do).

Example:

$ ksh -c 'echo "$((3.0 / 4))"'
0.75

When you write

df['Date'] = pd.to_datetime(df['Date'], errors='coerce')
df['Date'] = df['Date'].dt.strftime('%m/%d')

It can fixed

If for matching identical images ( same size/orientation )

// Compare two images by getting the L2 error (square-root of sum of squared error).
double getSimilarity( const Mat A, const Mat B ) {
if ( A.rows > 0 && A.rows == B.rows && A.cols > 0 && A.cols == B.cols ) {
    // Calculate the L2 relative error between images.
    double errorL2 = norm( A, B, CV_L2 );
    // Convert to a reasonable scale, since L2 error is summed across all pixels of the image.
    double similarity = errorL2 / (double)( A.rows * A.cols );
    return similarity;
}
else {
    //Images have a different size
    return 100000000.0;  // Return a bad value
}

Source

On Kotlin you can set width and height of any view directly using their virtual properties:

someView.layoutParams.width = 100
someView.layoutParams.height = 200

For people having a startTime (like 12h:30:30) and a duration (value in minutes like 120), you can guess the endTime like so:

const startTime = '12:30:00';
const durationInMinutes = '120';

const endTime = moment(startTime, 'HH:mm:ss').add(durationInMinutes, 'minutes').format('HH:mm');

// endTime is equal to "14:30"

You can use the below sample, also you dont need the else clause to print nothing!

 <?php if ( ($cart->count_product) > 0) { ?>
           <div class="my_class">
               <?php print $cart->count_product; ?> 
           </div>
 <?php } ?>

A view uses a query to pull data from the underlying tables.

A materialized view is a table on disk that contains the result set of a query.

Materialized views are primarily used to increase application performance when it isn't feasible or desirable to use a standard view with indexes applied to it. Materialized views can be updated on a regular basis either through triggers or by using the ON COMMIT REFRESH option. This does require a few extra permissions, but it's nothing complex. ON COMMIT REFRESH has been in place since at least Oracle 10.

For those of you rookies out there who may throw a SQL error when connecting to the DB from another machine(For example, at form load), you will find that when you first setup a datatable in C# which points to a SQL server database that it will setup a connection like this:

this.Table_nameTableAdapter.Fill(this.DatabaseNameDataSet.Table_name);

You may need to remove this line and replace it with something else like a traditional connection string as mentioned on MSDN, etc.

http://www.connectionstrings.com/sql-server-2008

In your example, you prepended your source string with AccountKey= but not your target string.

$c = $c -replace 'AccountKey=eKkij32jGEIYIEqAR5RjkKgf4OTiMO6SAyF68HsR/Zd/KXoKvSdjlUiiWyVV2+OUFOrVsd7jrzhldJPmfBBpQA==','AccountKey=DdOegAhDmLdsou6Ms6nPtP37bdw6EcXucuT47lf9kfClA6PjGTe3CfN+WVBJNWzqcQpWtZf10tgFhKrnN48lXA=='

By not including that in the target string, the resulting string will remove AccountKey= instead of replacing it. You correctly do this with the AccountName= example, which seems to support this conclusion since it is not giving you any problems. If you really mean to have that prepended, then this may resolve your issue.

Try it:

if (Objects.equals(gender, "Male")) {
    salutation ="Mr.";
} else if (Objects.equals(gender, "Female")) {
    salutation ="Ms.";
}

You can try : go to edit>preferencec>type.. select type > choose text engine options select east asian. Restart photoshop. Create new peroject. Try text tool again.

(if you want to use your project created with other text engine type) copy /paste all layers to new project.

Shift + Alt + F indents the whole file.

As said, the objectForKey: datatype is :(id)aKey whereas the valueForKey: datatype is :(NSString *)key.

For example:

 NSDictionary *dict = [NSDictionary dictionaryWithObjectsAndKeys:[NSArray arrayWithObject:@"123"],[NSNumber numberWithInteger:5], nil];

 NSLog(@"objectForKey : --- %@",[dict objectForKey:[NSNumber numberWithInteger:5]]);  
    //This will work fine and prints (    123    )  

 NSLog(@"valueForKey  : --- %@",[dict valueForKey:[NSNumber numberWithInteger:5]]); 
    //it gives warning "Incompatible pointer types sending 'NSNumber *' to parameter of type 'NSString *'"   ---- This will crash on runtime. 

So, valueForKey: will take only a string value and is a KVC method, whereas objectForKey: will take any type of object.

The value in objectForKey will be accessed by the same kind of object.

If I have the class:

public class MyClass
{
   public void MyMethod()
   {

   }
}

and I then do:

MyClass myClass = null;
myClass.MyMethod();

The second line throws this exception becuase I'm calling a method on a reference type object that is null (I.e. has not been instantiated by calling myClass = new MyClass())

The computer "name" is resolved from the IP address by the underlying DNS (Domain Name System) library of the OS. There's no universal concept of a computer name across OSes, but DNS is generally available. If the computer name hasn't been configured so DNS can resolve it, it isn't available.

import java.net.InetAddress;
import java.net.UnknownHostException;

String hostname = "Unknown";

try
{
    InetAddress addr;
    addr = InetAddress.getLocalHost();
    hostname = addr.getHostName();
}
catch (UnknownHostException ex)
{
    System.out.println("Hostname can not be resolved");
}

• First line : array created.
• Third line loop started from j = 1 to j = 28123
• Fourth line you give the variable x value (0) each time the loop is accessed.
• Fifth line you put the value of j in the index 0.
• Sixth line you do increment to the value x by 1.(but it will be reset to 0 at line 4)

You can use this for header: Important: Put the following on your PHP pages that you want to include the content.

<?php
//at top:
require('header.php'); 
 ?>
 <?php
// at bottom:
require('footer.php');
?>

You can also include a navbar globaly just use this instead:

 <?php
 // At top:
require('header.php'); 
 ?>
  <?php
// At bottom:
require('footer.php');
 ?>
 <?php
 //Wherever navbar goes:
require('navbar.php'); 
?>

In header.php:

 <!DOCTYPE html>
 <html lang="en">
 <head>
    <meta charset="utf-8">
 <meta name="viewport" content="width=device-width, initial-scale=1, shrink-to-fit=no">
 </head>
 <body> 

Do Not close Body or Html tags!
Include html here:

 <?php
 //Or more global php here:

 ?>

Footer.php:

Code here:

<?php
//code

?>

Navbar.php:

<p> Include html code here</p>
<?php
 //Include Navbar PHP code here
 
?>

Benifits:

• Cleaner main php file (index.php) script.
• Change the header or footer. etc to change it on all pages with the include— Good for alerts on all pages etc...
• Time Saving!
• Faster page loads!
• you can have as many files to include as needed!
• server sided!

The datetime class has a method strftime. The Python docs documents the different formats it accepts:

• Python 2: strftime() Behavior
• Python 3: strftime() Behavior

For this specific example, it would look something like:

my_datetime.strftime("%B %d, %Y")

First method you can try this

$department->department_name = $request->department_name;
$department->status = $request->status;
$department->save();

Another way to insert records into the database with create function

$department = new Department;           
// Another Way to insert records
$department->create($request->all());

return redirect('admin/departments');

You need to set the filledby in Department model

namespace App;

use Illuminate\Database\Eloquent\Model;

class Department extends Model
{
    protected $fillable = ['department_name','status'];
} 

From the command line, it's simply:

printf "compute sha1" | openssl sha1

You can invoke the library like this:

#include <stdio.h>
#include <string.h>
#include <openssl/sha.h>

int main()
{
    unsigned char ibuf[] = "compute sha1";
    unsigned char obuf[20];

    SHA1(ibuf, strlen(ibuf), obuf);

    int i;
    for (i = 0; i < 20; i++) {
        printf("%02x ", obuf[i]);
    }
    printf("\n");

    return 0;
}

Wrote a small class for doing this cleanly.

import tempfile

class FileModifierError(Exception):
    pass

class FileModifier(object):

    def __init__(self, fname):
        self.__write_dict = {}
        self.__filename = fname
        self.__tempfile = tempfile.TemporaryFile()
        with open(fname, 'rb') as fp:
            for line in fp:
                self.__tempfile.write(line)
        self.__tempfile.seek(0)

    def write(self, s, line_number = 'END'):
        if line_number != 'END' and not isinstance(line_number, (int, float)):
            raise FileModifierError("Line number %s is not a valid number" % line_number)
        try:
            self.__write_dict[line_number].append(s)
        except KeyError:
            self.__write_dict[line_number] = [s]

    def writeline(self, s, line_number = 'END'):
        self.write('%s\n' % s, line_number)

    def writelines(self, s, line_number = 'END'):
        for ln in s:
            self.writeline(s, line_number)

    def __popline(self, index, fp):
        try:
            ilines = self.__write_dict.pop(index)
            for line in ilines:
                fp.write(line)
        except KeyError:
            pass

    def close(self):
        self.__exit__(None, None, None)

    def __enter__(self):
        return self

    def __exit__(self, type, value, traceback):
        with open(self.__filename,'w') as fp:
            for index, line in enumerate(self.__tempfile.readlines()):
                self.__popline(index, fp)
                fp.write(line)
            for index in sorted(self.__write_dict):
                for line in self.__write_dict[index]:
                    fp.write(line)
        self.__tempfile.close()

Then you can use it this way:

with FileModifier(filename) as fp:
    fp.writeline("String 1", 0)
    fp.writeline("String 2", 20)
    fp.writeline("String 3")  # To write at the end of the file

Check the encoding before you pass to pandas. It will slow you down, but...

with open(path, 'r') as f:
    encoding = f.encoding 

df = pd.read_csv(path,sep=sep, encoding=encoding)

In python 3.7

The prompt command will echo text to the output:

prompt A useful comment.
select(*) from TableA;

Will be displayed as:

SQL> A useful comment.
SQL> 
  COUNT(*)
----------
     0

The best thing would be to link to the jQuery core is via google.
There are 3 reasons to do it this way,

• Decreased Latency
• Increased parallelism
• Better caching

      see:
      http://encosia.com/2008/12/10/3-reasons-why-you-should-let-google-host-jquery-for-you/

<script type="text/javascript" src="http://ajax.googleapis.com/ajax/libs/jquery/1.3.2/jquery.min.js"></script>
<script type="text/javascript">
 $(document).ready(function() {

Your code here.....

  });
</script>

I know this is an old question but anyway it might help someone.

I tend to use PHP_EOL for this purposes (due to cross-platform compatibility).

echo "line 1".PHP_EOL."line 2".PHP_EOL;

If you're planning to show the result in a browser then you have to use "<br>".

EDIT: since your exact question is about emails, things are a bit different. For pure text emails see Brendan Bullen's accepted answer. For HTML emails you simply use HTML formatting.

Copy all order entries of home folder .iml file into your /src/main/main.iml file. This will solve the problem.

I had the exact same issue. If you are using a relative path os.path.dirname(path) will only return the relative path. os.path.realpath does the trick:

>>> import os
>>> f = open('file.txt')
>>> os.path.realpath(f.name)

1. On the menu bar, select Window ? Preferences
2. Set the font size (General ? Appearance ? Colors and Fonts ? Structured Text Editors ? Structured Text Editor Text Font (set to default: Text Font) ? Edit...).
3. Save the preferences.

I was getting this exception every time I created a "new" project.

My solution was:

• Go menu Tools ? Extensions and Updates
• Not check the "Updates" link...search "asp.net". There was an update to Microsoft ASP.NET and Web Tools. Get it as AspNetWebFrameworksTools2015_KB3137909.exe and install it.

That fixed it for me.

Unfortunately, I ran into another exception:

"Exception has been thrown by the target of an invocation"

I disabled the FIPS setting Enabled DWORD value to zero.

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa\FipsAlgorithmPolicy]
Enabled=dword:00000000 And All fixed.

I have started writing one tutorial for everyone on this topic, see making gadgets for Windows 7.

If I understand your problem well you want the following things:

1. Have your media files stored in one single git repository, which is used by many projects
2. If you modify a media file in any of the projects in your local machine, it should immediately appear in every other project (so you don't want to commit+push+pull all the time)

Unfortunately there is no ultimate solution for what you want, but there are some things by which you can make your life easier.

First you should decide one important thing: do you want to store for every version in your project repository a reference to the version of the media files? So for example if you have a project called example.com, do you need know which style.css it used 2 weeks ago, or the latest is always (or mostly) the best?

If you don't need to know that, the solution is easy:

1. create a repository for the media files and one for each project
2. create a symbolic link in your projects which point to the locally cloned media repository. You can either create a relative symbolic link (e.g. ../media) and assume that everybody will checkout the project so that the media directory is in the same place, or write the name of the symbolic link into .gitignore, and everybody can decide where he/she puts the media files.

In most of the cases, however, you want to know this versioning information. In this case you have two choices:

1. Store every project in one big repository. The advantage of this solution is that you will have only 1 copy of the media repository. The big disadvantage is that it is much harder to switch between project versions (if you checkout to a different version you will always modify ALL projects)

2. Use submodules (as explained in answer 1). This way you will store the media files in one repository, and the projects will contain only a reference to a specific media repo version. But this way you will normally have many local copies of the media repository, and you cannot easily modify a media file in all projects.

If I were you I would probably choose the first or third solution (symbolic links or submodules). If you choose to use submodules you can still do a lot of things to make your life easier:

1. Before committing you can rename the submodule directory and put a symlink to a common media directory. When you're ready to commit, you can remove the symlink and remove the submodule back, and then commit.

2. You can add one of your copy of the media repository as a remote repository to all of your projects.

You can add local directories as a remote this way:

cd /my/project2/media
git remote add project1 /my/project1/media

If you modify a file in /my/project1/media, you can commit it and pull it from /my/project2/media without pushing it to a remote server:

cd /my/project1/media
git commit -a -m "message"
cd /my/project2/media
git pull project1 master

You are free to remove these commits later (with git reset) because you haven't shared them with other users.

// TypeScript

const today = new Date();
const firstDayOfYear = new Date(today.getFullYear(), 0, 1);

// Explicitly convert Date to Number
const pastDaysOfYear = ( Number(today) - Number(firstDayOfYear) );

Regex symbol to match at beginning of a line:

^

Add the string you're searching for (CTR) to the regex like this:

^CTR

Example: regex

That should be enough!

However, if you need to get the text from the whole line in your language of choice, add a "match anything" pattern .*:

^CTR.*

Example: more regex

If you want to get crazy, use the end of line matcher

$

Add that to the growing regex pattern:

^CTR.*$

Example: lets get crazy

Note: Depending on how and where you're using regex, you might have to use a multi-line modifier to get it to match multiple lines. There could be a whole discussion on the best strategy for picking lines out of a file to process them, and some of the strategies would require this:

Multi-line flag m (this is specified in various ways in various languages/contexts)

/^CTR.*/gm

Example: we had to use m on regex101

The std::string object returned by ss.str() is a temporary object that will have a life time limited to the expression. So you cannot assign a pointer to a temporary object without getting trash.

Now, there is one exception: if you use a const reference to get the temporary object, it is legal to use it for a wider life time. For example you should do:

#include <string>
#include <sstream>
#include <iostream>

using namespace std;

int main()
{
    stringstream ss("this is a string\n");

    string str(ss.str());

    const char* cstr1 = str.c_str();

    const std::string& resultstr = ss.str();
    const char* cstr2 = resultstr.c_str();

    cout << cstr1       // Prints correctly
        << cstr2;       // No more error : cstr2 points to resultstr memory that is still alive as we used the const reference to keep it for a time.

    system("PAUSE");

    return 0;
}

That way you get the string for a longer time.

Now, you have to know that there is a kind of optimisation called RVO that say that if the compiler see an initialization via a function call and that function return a temporary, it will not do the copy but just make the assigned value be the temporary. That way you don't need to actually use a reference, it's only if you want to be sure that it will not copy that it's necessary. So doing:

 std::string resultstr = ss.str();
 const char* cstr2 = resultstr.c_str();

would be better and simpler.

VS2019 > Tools > Options > Nuget Package Manager > General > Click on "Clear All Nuger Cache(s)"

It is called the Card Security Code (CSC) according to Wikipedia, but has also been known as other things, such as the Card Verification Value (CVV) or Card Verfication Code (CVC).

The second code, and the most cited, is CVV2 or CVC2. This CSC (also known as a CCID or Credit Card ID) is often asked for by merchants for them to secure "card not present" transactions occurring over the Internet, by mail, fax or over the phone. In many countries in Western Europe, due to increased attempts at card fraud, it is now mandatory to provide this code when the cardholder is not present in person.

Because this seems to be known by multiple names, and its name doesn't seem to be printed on the card itself, you'll probably (unfortunately) still need to tell your users how to find the code - ie by describing it as the "3 digit code on back of card".

2018 update

The situation has not improved, and is now worse - there are even more different names now. However, you can if you like use different terms depending on the card type:

• "CVC2" or "Card Validation Code" – MasterCard
• "CVV2" or "Card Verification Value 2" – Visa
• "CSC" or "Card Security Code" – American Express

Note that some American Express and Discover cards use a 4-digit code on the front of the card. See the above linked Wikipedia article for more.

Everything everyone is saying is correct so,

int[] aArray = {1,2,3};
List<int> list = aArray.OfType<int> ().ToList();

would turn aArray into a list, list. However the biggest thing that is missing from a lot of comments is that you need to have these 2 using statements at the top of your class

using System.Collections.Generic;
using System.Linq;

I hope this helps!

Yes. Regardless of what anyone else says, Eclipse contains some bug(s) that sometimes causes the workspace setting (e.g. 1.6 compliant) to be ignored. This is even when the per-project settings are disabled, the workspace settings are correct (1.6), the JRE is correctly set, there is only a 1.6 JRE defined, etc., all the things that people generally recommend when questions about this issue are posted to various forums (as they often are).

We hit this irregularly, but often, and typically when there is some unrelated issue with build-time dependencies or other project issues. It seems to fall into the general category of "unable to get Eclipse to recognize reality" issues that I always attribute, rightly or wrongly, to refresh issues with Eclipse' extensive metadata. Eclipse metadata is a blessing and a curse; when all is working well, it makes the tool exceedingly powerful and fast. But when there are problems, the extensive caching makes straightening out the issues more difficult - sometimes much more difficult - than with other tools.

java is the root JNDI namespace for resources. What the original snippet of code means is that the container the application was initially deployed in did not apply any additional namespaces to the JNDI context you retrieved (as an example, Tomcat automatically adds all resources to the namespace comp/env, so you would have to do dataSource = (javax.sql.DataSource) context.lookup("java:comp/env/jdbc/myDataSource"); if the resource reference name is jdbc/myDataSource).

To avoid having to change your legacy code I think if you register the datasource with the name myDataSource (remove the jdbc/) you should be fine. Let me know if that works.

In your case, it will produce an error. :-)

Set assigns an object reference. For all other assignments the (implicit, optional, and little-used) Let statement is correct:

Set object = New SomeObject
Set object = FunctionReturningAnObjectRef(SomeArgument)

Let i = 0
Let i = FunctionReturningAValue(SomeArgument)

' or, more commonly '

i = 0
i = FunctionReturningAValue(SomeArgument)

mystring = mystring.replace(/["']/g, "");

You can use this method, It is easy to understand and implement :

public static java.util.Date AddingHHMMSSToDate(java.util.Date date, int nombreHeure, int nombreMinute, int nombreSeconde) {
    Calendar calendar = Calendar.getInstance();
    calendar.setTime(date);
    calendar.add(Calendar.HOUR_OF_DAY, nombreHeure);
    calendar.add(Calendar.MINUTE, nombreMinute);
    calendar.add(Calendar.SECOND, nombreSeconde);
    return calendar.getTime();
}

You can take a look to the article Design and Implementation of an In-Game Memory Profiler in the book "Game Programming Gems 8".

It shows how to implement a low overhead semi-intrusive real-time memory profiler, source code provided in the CD-ROM.

This is a short way:

document.getElementById('mySelect').innerText = null;

One line, no for, no JQuery, simple.

You can assign the datasource as null of your data grid and then rebind it.

dg.DataSource = null;
dg.DataBind();

More or less this page has answers but all are not at one place. I was dealing with the same issue and spent quite a good time on it. Now i have a better understanding and i would like to share it here:

I Enabling Swagger ui with Spring websecurity:

If you have enabled Spring Websecurity by default it will block all the requests to your application and returns 401. However for the swagger ui to load in the browser swagger-ui.html makes several calls to collect data. The best way to debug is open swagger-ui.html in a browser(like google chrome) and use developer options('F12' key ). You can see several calls made when the page loads and if the swagger-ui is not loading completely probably some of them are failing.

you may need to tell Spring websecurity to ignore authentication for several swagger path patterns. I am using swagger-ui 2.9.2 and in my case below are the patterns that i had to ignore:

However if you are using a different version your's might change. you may have to figure out yours with developer option in your browser as i said before.

@Configuration
public class WebSecurityConfiguration extends WebSecurityConfigurerAdapter {
@Override
public void configure(WebSecurity web) throws Exception {
    web.ignoring().antMatchers("/v2/api-docs", "/configuration/ui", 
            "/swagger-resources/**", "/configuration/**", "/swagger-ui.html"
            , "/webjars/**", "/csrf", "/");
}
}

II Enabling swagger ui with interceptor

Generally you may not want to intercept requests that are made by swagger-ui.html. To exclude several patterns of swagger below is the code:

Most of the cases pattern for web security and interceptor will be same.

@Configuration
@EnableWebMvc
public class RetrieveCiamInterceptorConfiguration implements WebMvcConfigurer {

@Autowired
RetrieveInterceptor validationInterceptor;

@Override
public void addInterceptors(InterceptorRegistry registry) {

    registry.addInterceptor(validationInterceptor).addPathPatterns("/**")
    .excludePathPatterns("/v2/api-docs", "/configuration/ui", 
            "/swagger-resources/**", "/configuration/**", "/swagger-ui.html"
            , "/webjars/**", "/csrf", "/");
}

@Override
public void addResourceHandlers(ResourceHandlerRegistry registry) {
    registry.addResourceHandler("swagger-ui.html")
      .addResourceLocations("classpath:/META-INF/resources/");

    registry.addResourceHandler("/webjars/**")
      .addResourceLocations("classpath:/META-INF/resources/webjars/");
}

}

Since you may have to enable @EnableWebMvc to add interceptors you may also have to add resource handlers to swagger similar to i have done in the above code snippet.

You should combine a type pointcut with a method pointcut.

These pointcuts will do the work to find all public methods inside a class marked with an @Monitor annotation:

@Pointcut("within(@org.rejeev.Monitor *)")
public void beanAnnotatedWithMonitor() {}

@Pointcut("execution(public * *(..))")
public void publicMethod() {}

@Pointcut("publicMethod() && beanAnnotatedWithMonitor()")
public void publicMethodInsideAClassMarkedWithAtMonitor() {}

Advice the last pointcut that combines the first two and you're done!

If you're interested, I have written a cheat sheet with @AspectJ style here with a corresponding example document here.

You can add the button image as follows:

CKEDITOR.plugins.add('showtime',   //name of our plugin
{    
    requires: ['dialog'], //requires a dialog window
    init:function(a) {
  var b="showtime";
  var c=a.addCommand(b,new CKEDITOR.dialogCommand(b));
  c.modes={wysiwyg:1,source:1}; //Enable our plugin in both modes
  c.canUndo=true;
 
  //add new button to the editor
  a.ui.addButton("showtime",
  {
   label:'Show current time',
   command:b,
   icon:this.path+"showtime.png"   //path of the icon
  });
  CKEDITOR.dialog.add(b,this.path+"dialogs/ab.js") //path of our dialog file
 }
});

Here is the actual plugin with all steps described.

The best way to generate the unique random number is

<?php
     echo md5(uniqid(mt_rand(), true).microtime(true));
?>

Using mmv

mmv '*_*_*' '#1_#3' *.png

Right click on icon --> Properties --> Advanced --> Check checkbox run as Administrator and everytime it will open under Admin Mode (Same for Windows 8)

A callable piece of code (routine) can be a Sub (called for a side effect/what it does) or a Function (called for its return value) or a mixture of both. As the docs for MsgBox

Displays a message in a dialog box, waits for the user to click a button, and returns a value indicating which button the user clicked.

MsgBox(prompt[, buttons][, title][, helpfile, context])

indicate, this routine is of the third kind.

The syntactical rules of VBScript are simple:

Use parameter list () when calling a (routine as a) Function

If you want to display a message to the user and need to know the user's reponse:

Dim MyVar
MyVar = MsgBox ("Hello World!", 65, "MsgBox Example")
   ' MyVar contains either 1 or 2, depending on which button is clicked.

Don't use parameter list () when calling a (routine as a) Sub

If you want to display a message to the user and are not interested in the response:

MsgBox "Hello World!", 65, "MsgBox Example"

This beautiful simplicity is messed up by:

The design flaw of using () for parameter lists and to force call-by-value semantics

>> Sub S(n) : n = n + 1 : End Sub
>> n = 1
>> S n
>> WScript.Echo n
>> S (n)
>> WScript.Echo n
>>
2
2

S (n) does not mean "call S with n", but "call S with a copy of n's value". Programmers seeing that

>> s = "value"
>> MsgBox(s)

'works' are in for a suprise when they try:

>> MsgBox(s, 65, "MsgBox Example")
>>
Error Number:       1044
Error Description:  Cannot use parentheses when calling a Sub

The compiler's leniency with regard to empty () in a Sub call. The 'pure' Sub Randomize (called for the side effect of setting the random seed) can be called by

Randomize()

although the () can neither mean "give me your return value) nor "pass something by value". A bit more strictness here would force prgrammers to be aware of the difference in

Randomize n

and

Randomize (n)

The Call statement that allows parameter list () in Sub calls:

s = "value" Call MsgBox(s, 65, "MsgBox Example")

which further encourage programmers to use () without thinking.

(Based on What do you mean "cannot use parentheses?")

I had this problem, but the file was in UTF-8, it was just that somehow on character had come in that was not encoded in UTF-8. To solve the problem I did what is stated in this thread, i.e. I validated the file: How to check whether a file is valid UTF-8?

Basically you run the command:

$ iconv -f UTF-8 your_file -o /dev/null

And if there is something that is not encoded in UTF-8 it will give you the line and row numbers so that you can find it.

Swift 5 version of accepted answer:

let image = UIImage(named: "image_name")
let button = UIButton(type: UIButton.ButtonType.custom)
button.frame = CGRect(x: 100, y: 100, width: 200, height: 100)
button.setImage(image, for: .normal)
button.addTarget(self, action: #selector(function), for: .touchUpInside)

//button.backgroundColor = .lightGray
self.view.addSubview(button)

where of course

@objc func function() {...}

The image is aligned to center by default. You can change this by setting button's imageEdgeInsets, like this:

// In this case image is 40 wide and aligned to the left
button.imageEdgeInsets = UIEdgeInsets(top: 5, left: 5, bottom: 5, right: button.frame.width - 45)

In my case I showed DialogFragment in Activity. In this dialog fragment I wrote as in DialogFragment remove black border:

override fun onCreate(savedInstanceState: Bundle?) {
    super.onCreate(savedInstanceState)
    setStyle(STYLE_NO_FRAME, 0)
}

override fun onCreateDialog(savedInstanceState: Bundle?): Dialog {
    super.onCreateDialog(savedInstanceState)

    val dialog = Dialog(context!!, R.style.ErrorDialogTheme)
    val inflater = LayoutInflater.from(context)
    val view = inflater.inflate(R.layout.fragment_error_dialog, null, false)
    dialog.setTitle(null)
    dialog.setCancelable(true)
    dialog.setContentView(view)
    return dialog
}

Either remove setStyle(STYLE_NO_FRAME, 0) in onCreate() or chande/remove onCreateDialog. Because dialog settings have changed after the dialog has been created.

When want to get row size with size() function, below code can be used:

size(A,1)

Another usage for it:

[height, width] = size(A)

So, you can get 2 dimension of your matrix.

Note: Apply the class info_link to any link you want to get the info from.

<a class="info_link" href="~/Resumes/Resumes1271354404687.docx">
    ~/Resumes/Resumes1271354404687.docx
</a>

For href:

$(function(){
  $('.info_link').click(function(){
    alert($(this).attr('href'));
    // or alert($(this).hash();
  });
});

For Text:

$(function(){
  $('.info_link').click(function(){
    alert($(this).text());
  });
});

.

Update Based On Question Edit

You can get them like this now:

For href:

$(function(){
  $('div.res a').click(function(){
    alert($(this).attr('href'));
    // or alert($(this).hash();
  });
});

For Text:

$(function(){
  $('div.res a').click(function(){
    alert($(this).text());
  });
});

If you have additional types, edit the selector:

var formElements = new Array();
$("form :input").each(function(){
    formElements.push($(this));
});

All form elements are now in the array formElements.

Here's a LINQ solution which is virtually the same but more scalable:

new[] { "a", "b", "c" }.Any(c => s.Contains(c))

This is the correct way:

You should declare the length of the array after "="

Veicle[] cars = new Veicle[N];

The line

 Int16 answer = firstNo + secondNo;

is interpreted as

 Int16 answer = (Int32) (firstNo + secondNo);

Simply because there is no such thing as Int16 arithmetic.

The simple solution: Do not use Int16. Use Int32 or simply int.

int is your default integer type. short and long are only used in special cases.

If you need to increase MySQL Connections without MySQL restart do like below, also if you don't know configuration file, below use the mysqlworkbench or phpmyadmin or command prompt to run below queries.

mysql> show variables like 'max_connections';
+-----------------+-------+
| Variable_name   | Value |
+-----------------+-------+
| max_connections | 151   |
+-----------------+-------+
1 row in set (0.00 sec)

mysql> SET GLOBAL max_connections = 250;
Query OK, 0 rows affected (0.00 sec)

mysql> show variables like 'max_connections';
+-----------------+-------+
| Variable_name   | Value |
+-----------------+-------+
| max_connections | 250   |
+-----------------+-------+
1 row in set (0.00 sec)

These settings will change at MySQL Restart.

For permanent changes add below line in my.cnf and restart MySQL.

max_connections = 151

If you use Object Relational Mapping tools or will in the future I suggest Singular.

Some tools like LLBLGen can automatically correct plural names like Users to User without changing the table name itself. Why does this matter? Because when it's mapped you want it to look like User.Name instead of Users.Name or worse from some of my old databases tables naming tblUsers.strName which is just confusing in code.

My new rule of thumb is to judge how it will look once it's been converted into an object.

one table I've found that does not fit the new naming I use is UsersInRoles. But there will always be those few exceptions and even in this case it looks fine as UsersInRoles.Username.

If you are using Logger.getLogger(ClassName.class) then place your log4j.properties file in your class path:

yourproject/javaresoures/src/log4j.properties (Put inside src folder)

db.employe.find({ $and:[ {"dept":{ $exists:false }, "empno": { $in:[101,102] } } ] }).count();

Putting comments on the same line with commands: use & :: comment

color C          & :: set red font color
echo IMPORTANT INFORMATION
color            & :: reset the color to default

Explanation:

& separates two commands, so in this case color C is the first command and :: set red font color is the second one.

Important:

This statement with comment looks intuitively correct:

goto error1         :: handling the error

but it is not a valid use of the comment. It works only because goto ignores all arguments past the first one. The proof is easy, this goto will not fail either:

goto error1 handling the error

But similar attempt

color 17            :: grey on blue

fails executing the command due to 4 arguments unknown to the color command: ::, grey, on, blue.

It will only work as:

color 17     &      :: grey on blue

So the ampersand is inevitable.

This will also work

SELECT NAME 
FROM GEO_LOCATION
WHERE MODIFY_ON BETWEEN SYSDATE() - INTERVAL 2 HOUR AND SYSDATE()

Sometimes could missing the below line under <build> tag in pom.xml when packaging through maven. since src folder contains your java files

<sourceDirectory>src</sourceDirectory>

Sorry, Im a newbie myself and I had this issue:

./hello.py: line 1: syntax error near unexpected token "Hello World"' ./hello.py: line 1:print("Hello World")'

I added the file header for the python 'deal' as #!/usr/bin/python

Then simple executed the program with './hello.py'

$sql = "SELECT * FROM table";
$result = $conn->query($sql);

if (!$result) {
    trigger_error('Invalid query: ' . $conn->error);
}

check the error with mysqli_error() function

probably your query has some faults.

if you are talking about in the reference of String Class. so you can use

subString/split

for Explode & use String

concate

for Implode.

i think this - including null value = 0

 SELECT oi.id, 
         SUM(nvl(oi.quantity,0) * nvl(p.price,0)) AS total_qty 
    FROM ORDERITEM oi 
    JOIN PRODUCT p ON p.id = oi.productid 
   WHERE oi.orderid = @OrderId 
GROUP BY oi.id 

You can also use a while loop:

while (true) {
    //your code
}

Tested and working 100%

public class MainActivity extends ActionBarActivity {
    Context context = this;
    MediaPlayer mp;

    @Override
    public void onCreate(Bundle savedInstanceState) {
        super.onCreate(savedInstanceState);
        setContentView(R.layout.main_layout);
        mp = MediaPlayer.create(context, R.raw.sound);
        final Button b = (Button) findViewById(R.id.Button);
        b.setOnClickListener(new View.OnClickListener() {
            @Override
            public void onClick(View v) {

                try {
                    if (mp.isPlaying()) {
                        mp.stop();
                        mp.release();
                        mp = MediaPlayer.create(context, R.raw.sound);
                    } mp.start();
                } catch(Exception e) { e.printStackTrace(); }
            }
        });
    }
}

This was all we had to do

if (mp.isPlaying()) {
    mp.stop();
    mp.release();
    mp = MediaPlayer.create(context, R.raw.sound);
}

In case you like to keep the commit changes after deletion:

Note that this solution works if the commit to be removed is the last committed one.

1 - Copy the commit reference you like to go back to from the log:

git log

2 - Reset git to the commit reference:

 git reset <commit_ref>

3 - Stash/store the local changes from the wrong commit to use later after pushing to remote:

 git stash

4 - Push the changes to remote repository, (-f or --force):

git push -f

5 - Get back the stored changes to local repository:

git stash apply

7 - In case you have untracked/new files in the changes, you need to add them to git before committing:

git add .

6 - Add whatever extra changes you need, then commit the needed files, (or use a dot '.' instead of stating each file name, to commit all files in the local repository:

git commit -m "<new_commit_message>" <file1> <file2> ...

or

git commit -m "<new_commit_message>" .

You are absolutely correct in that respect. In small trivial programs where a variable must exist until the death of the program, there is no real benefit to deallocating the memory.

In fact, I had once been involved in a project where each execution of the program was very complex but relatively short-lived, and the decision was to just keep memory allocated and not destabilize the project by making mistakes deallocating it.

That being said, in most programs this is not really an option, or it can lead you to run out of memory.

Choose Open Transcript from the ... dropdown to the right of the vote up/down and share links.

This will open a Transcript scrolling div on the right side.

You can then use Copy. Note that you cannot use Select All but need to click the top line, then scroll to the bottom using the scroll thumb, and then shift-click on the last line.

Note that you can also search within this text using the normal web page search.

Open the assembly file in ILDASM and look @ the .assembly extern in the MANIFEST

There is a built-in middleware that makes it easier than writing a custom one.

Asp.Net Core 5 version:

app.UseExceptionHandler(a => a.Run(async context =>
{
    var exceptionHandlerPathFeature = context.Features.Get<IExceptionHandlerPathFeature>();
    var exception = exceptionHandlerPathFeature.Error;
    
    await context.Response.WriteAsJsonAsync(new { error = exception.Message });
}));

Older versions (they did not have WriteAsJsonAsync extension):

app.UseExceptionHandler(a => a.Run(async context =>
{
    var exceptionHandlerPathFeature = context.Features.Get<IExceptionHandlerPathFeature>();
    var exception = exceptionHandlerPathFeature.Error;
    
    var result = JsonConvert.SerializeObject(new { error = exception.Message });
    context.Response.ContentType = "application/json";
    await context.Response.WriteAsync(result);
}));

It should do pretty much the same, just a bit less code to write.

Important: Remember to add it before UseMvc (or UseRouting in .Net Core 3) as order is important.

First of all this is JavaScript and not C#

Then you cannot disable a div because it normally has no functionality. To disable a click event, you simply have to remove the event from the dom object. (bind and unbind)...

Have you tried the import text function.

Only Visual Studio 2015 Enterprise has code coverage built-in. See the feature matrix for details.

You can use the OpenCover.UI extension for code coverage check inside Visual Studio. It supports MSTest, nUnit, and xUnit.

The new version can be downloaded from here (release notes).

On Chrome this has proven to work well for me.

<a href="newsletter_01.pdf" target="_new">Read more</a>

Maybe I completely misread your question, but the "I am hoping to retain the columns that do not match after the bind" makes me think you are looking for a left join or right join similar to an SQL query. R has the merge function that lets you specify left, right, or inner joins similar to joining tables in SQL.

There is already a great question and answer on this topic here: How to join (merge) data frames (inner, outer, left, right)?

Try deleting the build folder(s) in your project and resync your gradle project to rebuild it. Also, like others have said in this post - instead of doing something like this:

compile 'com.android.support:support-v4:19.+'

do this:

compile 'com.android.support:support-v4:19.1.0'

Try this

long start_time = System.nanoTime();
resp = GeoLocationService.getLocationByIp(ipAddress);
long end_time = System.nanoTime();
double difference = (end_time - start_time) / 1e6;

What worked for me is moving the following code from page_load to page_prerender:

lstMain.DataBind();
Image img = (Image)lstMain.Items[0].FindControl("imgMain");

// Define the name and type of the client scripts on the page.
String csname1 = "PopupScript";
Type cstype = this.GetType();

// Get a ClientScriptManager reference from the Page class.
ClientScriptManager cs = Page.ClientScript;

// Check to see if the startup script is already registered.
if (!cs.IsStartupScriptRegistered(cstype, csname1))
{
    cs.RegisterStartupScript(cstype, csname1, "<script language=javascript> p=\"" + img.ClientID + "\"</script>");
}

You may wish to consider self-certifying your projects:

Self-certification, digital certificate, digital signatures

Use "read()" instead o fscanf:

ssize_t read(int fildes, void *buf, size_t nbyte);

DESCRIPTION

The read() function shall attempt to read nbyte bytes from the file associated with the open file descriptor, fildes, into the buffer pointed to by buf.

Here is an example:

http://cmagical.blogspot.com/2010/01/c-programming-on-unix-implementing-cat.html

Working part from that example:

f=open(argv[1],O_RDONLY);
while ((n=read(f,l,80)) > 0)
    write(1,l,n);

An alternate approach is to use getc/putc to read/write 1 char at a time. A lot less efficient. A good example: http://www.eskimo.com/~scs/cclass/notes/sx13.html

Unless you have more style sheets than that, you've messed up your break points:

#1 (max-width: 700px)
#2 (min-width: 701px) and (max-width: 900px)
#3 (max-width: 901px)

The 3rd media query is probably meant to be min-width: 901px. Right now, it overlaps #1 and #2, and only controls the page layout by itself when the screen is exactly 901px wide.

Edit for updated question:

(max-width: 640px)
(max-width: 800px)
(max-width: 1024px)
(max-width: 1280px)

Media queries aren't like catch or if/else statements. If any of the conditions match, then it will apply all of the styles from each media query it matched. If you only specify a min-width for all of your media queries, it's possible that some or all of the media queries are matched. In your case, a device that's 640px wide matches all 4 of your media queries, so all for style sheets are loaded. What you are most likely looking for is this:

(max-width: 640px)
(min-width: 641px) and (max-width: 800px)
(min-width: 801px) and (max-width: 1024px)
(min-width: 1025px)

Now there's no overlap. The styles will only apply if the device's width falls between the widths specified.

It's the "frame" or "range" clause of window functions, which are part of the SQL standard and implemented in many databases, including Teradata.

A simple example would be to calculate the average amount in a frame of three days. I'm using PostgreSQL syntax for the example, but it will be the same for Teradata:

WITH data (t, a) AS (
  VALUES(1, 1),
        (2, 5),
        (3, 3),
        (4, 5),
        (5, 4),
        (6, 11)
)
SELECT t, a, avg(a) OVER (ORDER BY t ROWS BETWEEN 1 PRECEDING AND 1 FOLLOWING)
FROM data
ORDER BY t

... which yields:

t  a  avg
----------
1  1  3.00
2  5  3.00
3  3  4.33
4  5  4.00
5  4  6.67
6 11  7.50

As you can see, each average is calculated "over" an ordered frame consisting of the range between the previous row (1 preceding) and the subsequent row (1 following).

When you write ROWS UNBOUNDED PRECEDING, then the frame's lower bound is simply infinite. This is useful when calculating sums (i.e. "running totals"), for instance:

WITH data (t, a) AS (
  VALUES(1, 1),
        (2, 5),
        (3, 3),
        (4, 5),
        (5, 4),
        (6, 11)
)
SELECT t, a, sum(a) OVER (ORDER BY t ROWS BETWEEN UNBOUNDED PRECEDING AND CURRENT ROW)
FROM data
ORDER BY t

yielding...

t  a  sum
---------
1  1    1
2  5    6
3  3    9
4  5   14
5  4   18
6 11   29

Here's another very good explanations of SQL window functions.

The compiler only knows that the code is or isn't reachable if you use "return". Think of Environment.Exit() as a function that you call, and the compiler don't know that it will close the application.

As stated in 1.7.12 Release Notes, you may use

$ git rebase -i --root

First off, remember that JavaScript is primarily a prototypal language, rather than a class-based language¹. Foo isn't a class, it's a function, which is an object. You can instantiate an object from that function using the new keyword which will allow you to create something similar to a class in a standard OOP language.

I'd suggest ignoring __proto__ most of the time because it has poor cross browser support, and instead focus on learning about how prototype works.

If you have an instance of an object created from a function² and you access one of its members (methods, attributes, properties, constants etc) in any way, the access will flow down the prototype hierarchy until it either (a) finds the member, or (b) doesn't find another prototype.

The hierarchy starts on the object that was called, and then searches its prototype object. If the prototype object has a prototype, it repeats, if no prototype exists, undefined is returned.

For example:

foo = {bar: 'baz'};
console.log(foo.bar); // logs "baz"

foo = {};
console.log(foo.bar); // logs undefined

function Foo(){}
Foo.prototype = {bar: 'baz'};
f = new Foo();
console.log(f.bar);
// logs "baz" because the object f doesn't have an attribute "bar"
// so it checks the prototype
f.bar = 'buzz';
console.log( f.bar ); // logs "buzz" because f has an attribute "bar" set

It looks to me like you've at least somewhat understood these "basic" parts already, but I need to make them explicit just to be sure.

In JavaScript, everything is an object³.

everything is an object.

function Foo(){} doesn't just define a new function, it defines a new function object that can be accessed using Foo.

This is why you can access Foo's prototype with Foo.prototype.

What you can also do is set more functions on Foo:

Foo.talk = function () {
  alert('hello world!');
};

This new function can be accessed using:

Foo.talk();

I hope by now you're noticing a similarity between functions on a function object and a static method.

Think of f = new Foo(); as creating a class instance, Foo.prototype.bar = function(){...} as defining a shared method for the class, and Foo.baz = function(){...} as defining a public static method for the class.

ECMAScript 2015 introduced a variety of syntactic sugar for these sorts of declarations to make them simpler to implement while also being easier to read. The previous example can therefore be written as:

class Foo {
  bar() {...}

  static baz() {...}
}

which allows bar to be called as:

const f = new Foo()
f.bar()

and baz to be called as:

Foo.baz()

_{1: class was a "Future Reserved Word" in the ECMAScript 5 specification, but ES6 introduces the ability to define classes using the class keyword.}

_{2: essentially a class instance created by a constructor, but there are many nuanced differences that I don't want to mislead you}

_{3: primitive values—which include undefined, null, booleans, numbers, and strings—aren't technically objects because they're low-level language implementations. Booleans, numbers, and strings still interact with the prototype chain as though they were objects, so for the purposes of this answer, it's easier to consider them "objects" even though they're not quite.}

You can work around this known bug in OpenJDK with this:

Map<Integer, Boolean> collect = list.stream()
        .collect(HashMap::new, (m,v)->m.put(v.getId(), v.getAnswer()), HashMap::putAll);

It is not that much pretty, but it works. Result:

1: true
2: true
3: null

(this tutorial helped me the most.)

EDIT:

Unlike Collectors.toMap, this will silently replace values if you have the same key multiple times, as @mmdemirbas pointed out in the comments. If you don't want this, look at the link in the comment.

On the (more general) question in title - to prevent Jenkins from failing you can prevent it from seeing exit code 1. Example for ping:

bash -c "ping 1.2.3.9999 -c 1; exit 0"

And now you can e.g. get output of ping:

output=`bash -c "ping 1.2.3.9999 -c 1; exit 0"`

Of course instead of ping ... You can use any command(s) - including git commit.

urlretrieve and requests.get are simple, however the reality not. I have fetched data for couple sites, including text and images, the above two probably solve most of the tasks. but for a more universal solution I suggest the use of urlopen. As it is included in Python 3 standard library, your code could run on any machine that run Python 3 without pre-installing site-package

import urllib.request
url_request = urllib.request.Request(url, headers=headers)
url_connect = urllib.request.urlopen(url_request)

#remember to open file in bytes mode
with open(filename, 'wb') as f:
    while True:
        buffer = url_connect.read(buffer_size)
        if not buffer: break

        #an integer value of size of written data
        data_wrote = f.write(buffer)

#you could probably use with-open-as manner
url_connect.close()

This answer provides a solution to HTTP 403 Forbidden when downloading file over http using Python. I have tried only requests and urllib modules, the other module may provide something better, but this is the one I used to solve most of the problems.

In Python everything has a type. A Python function will do anything it is asked to do if the type of arguments support it.

Example: foo will add everything that can be __add__ed ;) without worrying much about its type. So that means, to avoid failure, you should provide only those things that support addition.

def foo(a,b):
    return a + b

class Bar(object):
    pass

class Zoo(object):
    def __add__(self, other):
        return 'zoom'

if __name__=='__main__':
    print foo(1, 2)
    print foo('james', 'bond')
    print foo(Zoo(), Zoo())
    print foo(Bar(), Bar()) # Should fail

In case of lubuntu 14.04 use

sudo apt-get install lib32z1 lib32ncurses5 lib32bz2-1.0 lib32stdc++6

P.S-no need to restart the system.

Instead of adding "ws." before every Range, as suggested above, you can add "ws.activate" before Call instead.

This will get you into the worksheet you want to work on.

For some picky web services, the request needs to have the content type set to JSON and the body to be a JSON string. For example:

Invoke-WebRequest -UseBasicParsing http://example.com/service -ContentType "application/json" -Method POST -Body "{ 'ItemID':3661515, 'Name':'test'}"

or the equivalent for XML, etc.

Groupby A:

In [0]: grp = df.groupby('A')

Within each group, sum over B and broadcast the values using transform. Then sort by B:

In [1]: grp[['B']].transform(sum).sort('B')
Out[1]:
          B
2 -2.829710
5 -2.829710
1  0.253651
4  0.253651
0  0.551377
3  0.551377

Index the original df by passing the index from above. This will re-order the A values by the aggregate sum of the B values:

In [2]: sort1 = df.ix[grp[['B']].transform(sum).sort('B').index]

In [3]: sort1
Out[3]:
     A         B      C
2  baz -0.528172  False
5  baz -2.301539   True
1  bar -0.611756   True
4  bar  0.865408  False
0  foo  1.624345  False
3  foo -1.072969   True

Finally, sort the 'C' values within groups of 'A' using the sort=False option to preserve the A sort order from step 1:

In [4]: f = lambda x: x.sort('C', ascending=False)

In [5]: sort2 = sort1.groupby('A', sort=False).apply(f)

In [6]: sort2
Out[6]:
         A         B      C
A
baz 5  baz -2.301539   True
    2  baz -0.528172  False
bar 1  bar -0.611756   True
    4  bar  0.865408  False
foo 3  foo -1.072969   True
    0  foo  1.624345  False

Clean up the df index by using reset_index with drop=True:

In [7]: sort2.reset_index(0, drop=True)
Out[7]:
     A         B      C
5  baz -2.301539   True
2  baz -0.528172  False
1  bar -0.611756   True
4  bar  0.865408  False
3  foo -1.072969   True
0  foo  1.624345  False

input[name=username] { disabled: true; /* Does not work */ }

I know this question is quite old but for other users who come across this problem, I suppose the easiest way to disable input is simply by ':disabled'

<input type="text" name="username" value="admin" disabled />
<style type="text/css">
  input[name=username]:disabled {
    opacity: 0.5 !important; /* Fade effect */
    cursor: not-allowed; /* Cursor change to disabled state*/
  }
</style>

In reality, if you have some script to disable the input dynamically/automatically with javascript or jquery that would automatically disable based on the condition you add.

In jQuery for Example:

if (condition) {
// Make this input prop disabled state
  $('input').prop('disabled', true);
}
else {
// Do something else
}

Hope the answer in CSS helps.

Update for intellij idea 2017 3.2

I'm aware that this thread is quite old, the correct answer seems valid and there are a lot of working solutions out there, but I think the approach stated bellow might have an additional benefit regarding efficiency and elegance.

I need this behavior for all of my activities, so I created a class CustomActivity inheriting from the class Activity and "hooked" the dispatchTouchEvent function. There are mainly two conditions to take care of:

1. If focus is unchanged and someone is tapping outside of the current input field, then dismiss the IME
2. If focus has changed and the next focused element isn't an instance of any kind of an input field, then dismiss the IME

This is my result:

@Override
public boolean dispatchTouchEvent(MotionEvent ev) {
    if(ev.getAction() == MotionEvent.ACTION_UP) {
        final View view = getCurrentFocus();

        if(view != null) {
            final boolean consumed = super.dispatchTouchEvent(ev);

            final View viewTmp = getCurrentFocus();
            final View viewNew = viewTmp != null ? viewTmp : view;

            if(viewNew.equals(view)) {
                final Rect rect = new Rect();
                final int[] coordinates = new int[2];

                view.getLocationOnScreen(coordinates);

                rect.set(coordinates[0], coordinates[1], coordinates[0] + view.getWidth(), coordinates[1] + view.getHeight());

                final int x = (int) ev.getX();
                final int y = (int) ev.getY();

                if(rect.contains(x, y)) {
                    return consumed;
                }
            }
            else if(viewNew instanceof EditText || viewNew instanceof CustomEditText) {
                return consumed;
            }

            final InputMethodManager inputMethodManager = (InputMethodManager) getSystemService(Context.INPUT_METHOD_SERVICE);

            inputMethodManager.hideSoftInputFromWindow(viewNew.getWindowToken(), 0);

            viewNew.clearFocus();

            return consumed;
        }
    }       

    return super.dispatchTouchEvent(ev);
}

Side note: Additionally I assign these attributes to the root view making it possible to clear focus on every input field and preventing input fields gaining focus on activity startup (making the content view the "focus catcher"):

@Override
protected void onCreate(Bundle savedInstanceState) {
    super.onCreate(savedInstanceState);

    final View view = findViewById(R.id.content);

    view.setFocusable(true);
    view.setFocusableInTouchMode(true);
}

This works quite nicely for IOS, but should also work for cocoa.

NSString *bundleRoot = [[NSBundle mainBundle] bundlePath];
NSFileManager *manager = [NSFileManager defaultManager];
NSDirectoryEnumerator *direnum = [manager enumeratorAtPath:bundleRoot];
NSString *filename;

while ((filename = [direnum nextObject] )) {

    //change the suffix to what you are looking for
    if ([filename hasSuffix:@".data"]) {   

        // Do work here
        NSLog(@"Files in resource folder: %@", filename);            
    }       
}

The solutions already posted came with the sideffect, that the first .show() call did not animate the ActionBar for me. I got another nice solution, which fixed that:

Create a transparent drawable - something like that:

<shape xmlns:android="http://schemas.android.com/apk/res/android">
    <solid
       android:color="#00000000" />
</shape>

Set the actual actionbar background to a invisible custom view which you set on the actionbar:

getSupportActionBar().setCustomView(R.layout.actionbar_custom_layout);
      getSupportActionBar().setDisplayOptions(ActionBar.DISPLAY_SHOW_CUSTOM,
              ActionBar.DISPLAY_SHOW_CUSTOM | ActionBar.DISPLAY_SHOW_HOME | ActionBar.DISPLAY_SHOW_TITLE);

Set the transparent background for the actionbar in onCreate:

getSupportActionBar().setBackgroundDrawable(getResources().getDrawable(R.drawable.background_transparent));

Imortant: Don't hide the actionbar immediately in onCreate, but with a little delay later - e.g. when the layout is finished with creation:

getWindow().getDecorView().getViewTreeObserver().addOnGlobalLayoutListener(new OnGlobalLayoutListener() {
                @Override
                public void onGlobalLayout() {
                    getSupportActionBar().hide();
                }
            });

Before your first .show() call set the custom view visible:

_actionbarRoot.setVisibility(View.VISIBLE);
getSupportActionBar().show();

I think that would be better if we use directly the split function

String toSplit = "/abc/def/ghfj.doc";

String result[] = toSplit.split("/");

String returnValue = result[result.length - 1]; //equals "ghfj.doc"

There's an ELSE in the DOS batch language? Back in the days when I did more of this kinda thing, there wasn't.

If my theory is correct and your ELSE is being ignored, you may be better off doing

IF NOT EXIST file GOTO label

...which will also save you a line of code (the one right after your IF).

Second, I vaguely remember some kind of bug with testing for the existence of directories. Life would be easier if you could test for the existence of a file in that directory. If there's no file you can be sure of, something to try (this used to work up to Win95, IIRC) would be to append the device file name NUL to your directory name, e.g.

IF NOT EXIST C:\dir\NUL GOTO ...

I'd suggest that the -i means it does match "ABC", but the difference is in the output. -i doesn't manipulate the input, so it won't change "ABC" to "abc" because you specified "abc" as the pattern. -o says it only shows the part of the output that matches the pattern specified, it doesn't say about matching input.

The output of echo "ABC" | grep -i abc is ABC, the -o shows output matching "abc" so nothing shows:

Naos:~ mattlacey$ echo "ABC" | grep -i abc | grep -o abc
Naos:~ mattlacey$ echo "ABC" | grep -i abc | grep -o ABC
ABC

Here is a visual presentation of the approved answer.

Use console.log(JSON.stringify(result)) to get the JSON in a string format.

EDIT: If your intention is to get the id and other properties from the result object and you want to see it console to know if its there then you can check with hasOwnProperty and access the property if it does exist:

var obj = {id : "007", name : "James Bond"};
console.log(obj);                    // Object { id: "007", name: "James Bond" }
console.log(JSON.stringify(obj));    //{"id":"007","name":"James Bond"}
if (obj.hasOwnProperty("id")){
    console.log(obj.id);             //007
}

This is my solution, feedback is welcome.. :)

$('input').keydown( function (event) { //event==Keyevent
    if(event.which == 13) {
        var inputs = $(this).closest('form').find(':input:visible');
        inputs.eq( inputs.index(this)+ 1 ).focus();
        event.preventDefault(); //Disable standard Enterkey action
    }
    // event.preventDefault(); <- Disable all keys  action
});

Whilst, as has been pointed out, it is possible to see the current default socket buffer sizes in /proc, it is also possible to check them using sysctl (Note: Whilst the name includes ipv4 these sizes also apply to ipv6 sockets - the ipv6 tcp_v6_init_sock() code just calls the ipv4 tcp_init_sock() function):

 sysctl net.ipv4.tcp_rmem
 sysctl net.ipv4.tcp_wmem

However, the default socket buffers are just set when the sock is initialised but the kernel then dynamically sizes them (unless set using setsockopt() with SO_SNDBUF). The actual size of the buffers for currently open sockets may be inspected using the ss command (part of the iproute package), which can also provide a bunch more info on sockets like congestion control parameter etc. E.g. To list the currently open TCP (t option) sockets and associated memory (m) information:

ss -tm

Here's some example output:

State       Recv-Q Send-Q        Local Address:Port        Peer Address:Port
ESTAB       0      0             192.168.56.102:ssh        192.168.56.1:56328
skmem:(r0,rb369280,t0,tb87040,f0,w0,o0,bl0,d0)

Here's a brief explanation of skmem (socket memory) - for more info you'll need to look at the kernel sources (e.g. sock.h):

r:sk_rmem_alloc
rb:sk_rcvbuf          # current receive buffer size
t:sk_wmem_alloc
tb:sk_sndbuf          # current transmit buffer size
f:sk_forward_alloc
w:sk_wmem_queued      # persistent transmit queue size
o:sk_omem_alloc
bl:sk_backlog
d:sk_drops

class Second:
    def __init__(self, data):
        self.data = data

class First:
    def SecondClass(self, data):
        return Second(data)

FirstClass = First()
SecondClass = FirstClass.SecondClass('now you see me')
print SecondClass.data

Actually your command line arguments are practically like an array already. At least, you can treat the $@ variable much like an array. That said, you can convert it into an actual array like this:

myArray=( "$@" )

If you just want to type some arguments and feed them into the $@ value, use set:

$ set -- apple banana "kiwi fruit"
$ echo "$#"
3
$ echo "$@"
apple banana kiwi fruit

Understanding how to use the argument structure is particularly useful in POSIX sh, which has nothing else like an array.

I used the property

display: table;

and

display: table-cell;

to achieve the same.Link to fiddle below shows 3 tables wrapped in divs and these divs are further wrapped in a parent div

<div id='content'>
   <div id='div-1'><!-- COntains table --></div>
   <div id='div-2'><!-- contains two more divs that require to be arranged one below other --></div>
</div>

Here is the jsfiddle: http://jsfiddle.net/vikikamath/QU6WP/1/ I thought this might be helpful to someone looking to set divs in same line without using display-inline

Most people use docker compose with networks. The documentation states:

The Docker network feature supports creating networks without the need to expose ports within the network, for detailed information see the overview of this feature).

Which means that if you use networks for communication between containers you don't need to worry about exposing ports.

A bit late to the party here but here's how simple this is:

ViewBag.Countries = new SelectList(countries.GetCountries(), "id", "countryName", "82");

this uses my method getcountries to populate a model called countries, obviousley you would replace this with whatever your datasource is, a model etc, then sets the id as the value in the selectlist. then just add the last param, in this case "82" to select the default selected item.

[edit] Here's how to use this in Razor:

@Html.DropDownListFor(model => model.CountryId, (IEnumerable<SelectListItem>)ViewBag.Countries, new { @class = "form-control" })

Important: Also, 1 other thing to watch out for, Make sure the model field that you use to store the selected Id (in this case model.CountryId) from the dropdown list is nullable and is set to null on the first page load. This one gets me every time.

Hope this saves someone some time.

I don't think you can do that in Java. Best bet is to just put the code in the last case of the range.

switch (num) {
  case 1: case 2: case 3: case 4: case 5: 
     System.Out.Println("testing case 1 to 5");
     break;
  case 6: case 7: case 8: case 9: case 10:
     System.Out.Println("testing case 6 to 10");
     break;
  default:
     //
}

Here's how I understand it:

What percent does x lie in a range

Let's assume you have a range from 0 to 100. Given an arbitrary number from that range, what "percent" from that range does it lie in? This should be pretty simple, 0 would be 0%, 50 would be 50% and 100 would be 100%.

Now, what if your range was 20 to 100? We cannot apply the same logic as above (divide by 100) because:

20 / 100

doesn't give us 0 (20 should be 0% now). This should be simple to fix, we just need to make the numerator 0 for the case of 20. We can do that by subtracting:

(20 - 20) / 100

However, this doesn't work for 100 anymore because:

(100 - 20) / 100

doesn't give us 100%. Again, we can fix this by subtracting from the denominator as well:

(100 - 20) / (100 - 20)

A more generalized equation for finding out what % x lies in a range would be:

(x - MIN) / (MAX - MIN)

Scale range to another range

Now that we know what percent a number lies in a range, we can apply it to map the number to another range. Let's go through an example.

old range = [200, 1000]
new range = [10, 20]

If we have a number in the old range, what would the number be in the new range? Let's say the number is 400. First, figure out what percent 400 is within the old range. We can apply our equation above.

(400 - 200) / (1000 - 200) = 0.25

So, 400 lies in 25% of the old range. We just need to figure out what number is 25% of the new range. Think about what 50% of [0, 20] is. It would be 10 right? How did you arrive at that answer? Well, we can just do:

20 * 0.5 = 10

But, what about from [10, 20]? We need to shift everything by 10 now. eg:

((20 - 10) * 0.5) + 10

a more generalized formula would be:

((MAX - MIN) * PERCENT) + MIN

To the original example of what 25% of [10, 20] is:

((20 - 10) * 0.25) + 10 = 12.5

So, 400 in the range [200, 1000] would map to 12.5 in the range [10, 20]

TLDR

To map x from old range to new range:

OLD PERCENT = (x - OLD MIN) / (OLD MAX - OLD MIN)
NEW X = ((NEW MAX - NEW MIN) * OLD PERCENT) + NEW MIN

git revert makes a new commit

git revert simply creates a new commit that is the opposite of an existing commit.

It leaves the files in the same state as if the commit that has been reverted never existed. For example, consider the following simple example:

$ cd /tmp/example
$ git init
Initialized empty Git repository in /tmp/example/.git/
$ echo "Initial text" > README.md
$ git add README.md
$ git commit -m "initial commit"
[master (root-commit) 3f7522e] initial commit
 1 file changed, 1 insertion(+)
 create mode 100644 README.md
$ echo "bad update" > README.md 
$ git commit -am "bad update"
[master a1b9870] bad update
 1 file changed, 1 insertion(+), 1 deletion(-)

In this example the commit history has two commits and the last one is a mistake. Using git revert:

$ git revert HEAD
[master 1db4eeb] Revert "bad update"
 1 file changed, 1 insertion(+), 1 deletion(-)

There will be 3 commits in the log:

$ git log --oneline
1db4eeb Revert "bad update"
a1b9870 bad update
3f7522e initial commit

So there is a consistent history of what has happened, yet the files are as if the bad update never occured:

cat README.md 
Initial text

It doesn't matter where in the history the commit to be reverted is (in the above example, the last commit is reverted - any commit can be reverted).

Closing questions

do you have to do something else after?

A git revert is just another commit, so e.g. push to the remote so that other users can pull/fetch/merge the changes and you're done.

Do you have to commit the changes revert made or does revert directly commit to the repo?

git revert is a commit - there are no extra steps assuming reverting a single commit is what you wanted to do.

Obviously you'll need to push again and probably announce to the team.

Indeed - if the remote is in an unstable state - communicating to the rest of the team that they need to pull to get the fix (the reverting commit) would be the right thing to do :).

Edit the build path in this order, this worked for me.

Make sure the /gen is before /src

You should be able to specify the whole path to the destination of your choice. E.g.:

plt.savefig('E:\New Folder\Name of the graph.jpg')

You say you've had problems with Navicat. For the record, I use Navicat and I haven't experienced the issue you describe. You might want to dig around, see if there's a reason for your problem and/or a solution, because given the question asked, my first recommendation would have been Navicat.

But if you want alternative suggestions, here are a few that I know of and have used:

MySQL has its own tool which you can download for free, called MySQL Workbench. Download it from here: http://wb.mysql.com/. My experience is that it's powerful, but I didn't really like the UI. But that's just my personal taste.

Another free program you might want to try is HeidiSQL. It's more similar to Navicat than MySQL Workbench. A colleague of mine loves it.

(interesting to note, by the way, that MariaDB (the forked version of MySQL) is currently shipped with HeidiSQL as its GUI tool)

Finally, if you're running a web server on your machine, there's always the option of a browser-based tool like PHPMyAdmin. It's actually a surprisingly powerful piece of software.

Probably the best cross browser solution for pdf display on web pages is to use the Mozilla PDF.js project code, it can be run as a node.js service and used as follows

<iframe style="width:100%;height:500px" src="http://www.mysite.co.uk/libs/pdfjs/web/viewer.html?file="http://www.mysite.co.uk/mypdf.pdf"></iframe>

A tutorial on how to use pdf.js can be found at this ejectamenta blog article

This worked well for me

select owner, table_name, nvl(num_rows,-1) 
from all_tables 
--where table_name in ('cats', 'dogs')
order by nvl(num_rows,-1) desc

from https://livesql.oracle.com/apex/livesql/file/content_EPJLBHYMPOPAGL9PQAV7XH14Q.html

Go to Anaconda Naviagator, find spyder,click settings in the top right corner of the spyder app.click update tab

Okay, the .NET 2.0 answers:

If you don't need to clone the values, you can use the constructor overload to Dictionary which takes an existing IDictionary. (You can specify the comparer as the existing dictionary's comparer, too.)

If you do need to clone the values, you can use something like this:

public static Dictionary<TKey, TValue> CloneDictionaryCloningValues<TKey, TValue>
   (Dictionary<TKey, TValue> original) where TValue : ICloneable
{
    Dictionary<TKey, TValue> ret = new Dictionary<TKey, TValue>(original.Count,
                                                            original.Comparer);
    foreach (KeyValuePair<TKey, TValue> entry in original)
    {
        ret.Add(entry.Key, (TValue) entry.Value.Clone());
    }
    return ret;
}

That relies on TValue.Clone() being a suitably deep clone as well, of course.

It's sad that Oracle doesn't allow this, I get asked to do this by developers all the time..

Here's a slightly dangerous, somewhat quick and dirty method:

1. Ensure you have enough space to copy the Table
2. Note any Constraints, Grants, Indexes, Synonyms, Triggers, um.. maybe some other stuff - that belongs to a Table - that I haven't thought about?
3. CREATE TABLE table_right_columns AS SELECT column1 column3, column2 FROM table_wrong_columns; -- Notice how we correct the position of the columns :)
4. DROP TABLE table_wrong_columns;
5. 'ALTER TABLE table_right_columns RENAME TO table_wrong_columns;`
6. Now the yucky part: recreate all those items you noted in step 2 above
7. Check what code is now invalid, and recompile to check for errors

And next time you create a table, please consider the future requirements! ;)

Try this one:

<button class="button" onclick="$('#target').toggle();">
    Show/Hide
</button>
<div id="target" style="display: none">
    Hide show.....
</div>

Here's some sample code:

Uri notification = RingtoneManager.getDefaultUri(RingtoneManager.TYPE_NOTIFICATION);
MediaPlayer mediaPlayer = MediaPlayer.create(getApplicationContext(), notification);
mediaPlayer.start();

open terminal

\curl -sSL https://get.rvm.io | bash -s stable

restart terminal then

rvm install ruby-2.4.2

check ruby version it should be 2.4.2

Instead of loading a gigantic log file in an editor, I'm using Unix command line tools like grep, tail, gawk, etc. to filter the interesting parts into a much smaller file and then, I open that.

On Windows, try Cygwin.

For read-only controls they are the same. For 2 way databinding, using a datasource in which you want to update, insert, etc with declarative databinding, you'll need to use Bind.

Imagine for example a GridView with a ItemTemplate and EditItemTemplate. If you use Bind or Eval in the ItemTemplate, there will be no difference. If you use Eval in the EditItemTemplate, the value will not be able to be passed to the Update method of the DataSource that the grid is bound to.

UPDATE: I've come up with this example:

<%@ Page Language="C#" %>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">

<html xmlns="http://www.w3.org/1999/xhtml">
<head runat="server">
    <title>Data binding demo</title>
</head>
<body>
    <form id="form1" runat="server">
        <asp:GridView 
            ID="grdTest" 
            runat="server" 
            AutoGenerateEditButton="true" 
            AutoGenerateColumns="false" 
            DataSourceID="mySource">
            <Columns>
                <asp:TemplateField>
                    <ItemTemplate>
                        <%# Eval("Name") %>
                    </ItemTemplate>
                    <EditItemTemplate>
                        <asp:TextBox 
                            ID="edtName" 
                            runat="server" 
                            Text='<%# Bind("Name") %>' 
                        />
                    </EditItemTemplate>
                </asp:TemplateField>
            </Columns>
        </asp:GridView>
    </form>

    <asp:ObjectDataSource 
        ID="mySource" 
        runat="server"
        SelectMethod="Select" 
        UpdateMethod="Update" 
        TypeName="MyCompany.CustomDataSource" />
</body>
</html>

And here's the definition of a custom class that serves as object data source:

public class CustomDataSource
{
    public class Model
    {
        public string Name { get; set; }
    }

    public IEnumerable<Model> Select()
    {
        return new[] 
        {
            new Model { Name = "some value" }
        };
    }

    public void Update(string Name)
    {
        // This method will be called if you used Bind for the TextBox
        // and you will be able to get the new name and update the
        // data source accordingly
    }

    public void Update()
    {
        // This method will be called if you used Eval for the TextBox
        // and you will not be able to get the new name that the user
        // entered
    }
}

This isn't pretty, but it works:

<script type="text/javascript">
  document.write('<script type="text/javascript" src="other.js"></script>');
</script>

<script type="text/javascript">
  functionFromOther();
</script>

Or

<script type="text/javascript">
  document.write('<script type="text/javascript" src="other.js"></script>');
  window.onload = function() {
    functionFromOther();
  };
</script>

The script must be included either in a separate <script> tag or before window.onload().

This will not work:

<script type="text/javascript">
  document.write('<script type="text/javascript" src="other.js"></script>');
  functionFromOther(); // Error
</script>

The same can be done with creating a node, as Pointy did, but only in FF. You have no guarantee when the script will be ready in other browsers.

Being an XML Purist I really hate this. But it does work predictably. You could easily wrap those ugly document.write()s so you don't have to look at them. You could even do tests and create a node and append it then fall back on document.write().

The padding inside a table-divider (TD) is a padding property applied to the cell itself.

CSS

td, th {padding:0}

The spacing in-between the table-dividers is a space between cell borders of the TABLE. To make it effective, you have to specify if your table cells borders will 'collapse' or be 'separated'.

CSS

table, td, th {border-collapse:separate}
table {border-spacing:6px}

Try this : https://www.google.ca/search?num=100&newwindow=1&q=css+table+cellspacing+cellpadding+site%3Astackoverflow.com ( 27 100 results )

SecurityElement.Escape(string s)

I made API sending data via form on website to prosperworks based on @Rocket Hazmat, @dbau and @maraca code. I hope, it will help somebody:

<?php

if(isset($_POST['submit'])) {
    //form's fields name:
    $name = $_POST['nameField'];
    $email = $_POST['emailField'];

    //API url:
    $url = 'https://api.prosperworks.com/developer_api/v1/leads';

    //JSON data(not exact, but will be compiled to JSON) file:
    //add as many data as you need (according to prosperworks doc):
    $data = array(
                            'name' => $name,
                            'email' => array('email' => $email)
                        );

    //sending request (according to prosperworks documentation):
    // use key 'http' even if you send the request to https://...
    $options = array(
        'http' => array(
            'header'  => "Content-Type: application/json\r\n".
             "X-PW-AccessToken: YOUR_TOKEN_HERE\r\n".
             "X-PW-Application:developer_api\r\n".
             "X-PW-UserEmail: YOUR_EMAIL_HERE\r\n",
            'method'  => 'POST',
            'content' => json_encode($data)
        )
    );

    //engine:
    $context  = stream_context_create($options);
    $result = file_get_contents($url, false, $context);
    if ($result === FALSE) { /* Handle error */ }
    //compiling to JSON (as wrote above):
    $resultData = json_decode($result, TRUE);
    //display what was sent:
    echo '<h2>Sent: </h2>';
    echo $resultData['published'];
    //dump var:
    var_dump($result);

}
?>
<html>
    <head>
    </head>

    <body>

        <form action="" method="POST">
            <h1><?php echo $msg; ?></h1>
            Name: <input type="text" name="nameField"/>
            <br>
            Email: <input type="text" name="emailField"/>
            <input type="submit" name="submit" value="Send"/>
        </form>

    </body>
</html>

I just want to point out that the Session ID cookie is not removed when using Session.Abandon as others said.

When you abandon a session, the session ID cookie is not removed from the browser of the user. Therefore, as soon as the session has been abandoned, any new requests to the same application will use the same session ID but will have a new session state instance. At the same time, if the user opens another application within the same DNS domain, the user will not lose their session state after the Abandon method is called from one application.

Sometimes, you may not want to reuse the session ID. If you do and if you understand the ramifications of not reusing the session ID, use the following code example to abandon a session and to clear the session ID cookie:

Session.Abandon();
Response.Cookies.Add(new HttpCookie("ASP.NET_SessionId", ""));

This code example clears the session state from the server and sets the session state cookie to null. The null value effectively clears the cookie from the browser.

http://support.microsoft.com/kb/899918

I think this will do:

$('#'+div_id+' .widget-head > span').text("new dialog title");

So to put it all together, checking for Nan, infinity and complex numbers (it would seem they are specified with j, not i, i.e. 1+2j) it results in:

def is_number(s):
    try:
        n=str(float(s))
        if n == "nan" or n=="inf" or n=="-inf" : return False
    except ValueError:
        try:
            complex(s) # for complex
        except ValueError:
            return False
    return True

You need to follow a few steps to debug properly.

1) mvn clean dependency:tree Take a look at the output to see exactly what you get and verify your dependencies are all there.

2) mvn clean compile. Does this fail? If not does that mean you only get the error in Eclipse?

You mentioned in a comment "And I run both commands above but I am getting this error". Did mvn clean compile work? Or did you get an error for that as well? If it worked then it's just an IDE problem and I'd look at the m2eclipse plugin. Better still, use IntelliJ as the free version has better maven support than Eclipse ;-)

Some style things ...

People often add too many dependencies in their pom file when they don't need to. If you take a look at a couple of links in mavenrepository.com you can see that spring-oxm and spring-jdbc both depend on spring-core so you don't need to add that explicitly (for example). mvn clean dependency:tree will show you what is coming in after all of that, but this is more tidying.

spring-batch-test should be test scope.

Pay attention to your dependency scope I was having the issue where when I invoke clean compile via Intellij, the pom would get downloaded, but the jar would not. There was a xxx.jar.lastUpdated file created. Then realized that the dependency scope was test, but I was triggering the compile. I deleted the repos, and triggered the mvn test, and issue was resolved.

If you have standart output redirect to "nohup.out" just see who use this file

lsof | grep nohup.out

SOAP uses WSDL for communication btw consumer and provider, whereas REST just uses XML or JSON to send and receive data

WSDL defines contract between client and service and is static by its nature. In case of REST contract is somewhat complicated and is defined by HTTP, URI, Media Formats and Application Specific Coordination Protocol. It's highly dynamic unlike WSDL.

SOAP doesn't return human readable result, whilst REST result is readable with is just plain XML or JSON

This is not true. Plain XML or JSON are not RESTful at all. None of them define any controls(i.e. links and link relations, method information, encoding information etc...) which is against REST as far as messages must be self contained and coordinate interaction between agent/client and service.

With links + semantic link relations clients should be able to determine what is next interaction step and follow these links and continue communication with service.

It is not necessary that messages be human readable, it's possible to use cryptic format and build perfectly valid REST applications. It doesn't matter whether message is human readable or not.

Thus, plain XML(application/xml) or JSON(application/json) are not sufficient formats for building REST applications. It's always reasonable to use subset of these generic media types which have strong semantic meaning and offer enough control information(links etc...) to coordinate interactions between client and server.

• For more details regarding control information I highly recommend to read this: http://www.amundsen.com/hypermedia/hfactor/
• Web Linking: http://tools.ietf.org/html/rfc5988
• Registered link relations: http://www.iana.org/assignments/link-relations/link-relations.xml

REST is over only HTTP

Not true, HTTP is most widely used and when we talk about REST web services we just assume HTTP. HTTP defines interface with it's methods(GET, POST, PUT, DELETE, PATCH etc) and various headers which can be used uniformly for interacting with resources. This uniformity can be achieved with other protocols as well.

P.S. Very simple, yet very interesting explanation of REST: http://www.looah.com/source/view/2284